Prusa Generic TPU @MK4S

Volumic · FLEX · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Prusa Generic TPU @MK4S

Compatible printers (5)

Prusa MK4S 0.3 nozzle
Prusa MK4S 0.4 nozzle
Prusa MK4S 0.5 nozzle
Prusa MK4S HF0.4 nozzle
Prusa MK4S HF0.5 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: FLEX overridden
was TPU (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 overridden
was 1.24 (inherited)
Cost (/kg): 82 overridden
was 35 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 100 (inherited)
Fan maximum (%): 50 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 5 (inherited)

Flow

Flow ratio: 1.08 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 3 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 2.5 overridden
was nil (inherited)
Retraction speed (mm/s): 60 overridden
was nil (inherited)
Deretraction speed (mm/s): 20 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	50 overridden was 40	50 overridden was 40
Textured PEI Plate	50 inherited	40 inherited

Custom G-code

filament_start_gcode overridden

M900 K0 ; Filament gcode

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa MK4S 0.3 nozzle, Prusa MK4S 0.4 nozzle, Prusa MK4S 0.5 nozzle, Prusa MK4S HF0.4 nozzle, Prusa MK4S HF0.5 nozzle overridden
default filament colour: #008000 overridden
filament id: Generic FLEX @MK4S overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: 2 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: 0 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 70 overridden
was 100 (inherited)
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": "50",
  "fan_min_speed": "30",
  "filament_cost": [
    "82"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": "0",
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": "0",
  "hot_plate_temp": "50",
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": "230",
  "overhang_fan_speed": "70",
  "filament_flow_ratio": "1.08",
  "slow_down_min_speed": "15",
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": "10",
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": "60",
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": "2.5",
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": "20",
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": "3",
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": "50",
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "3"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "230",
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": "2",
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Generic FLEX @MK4S",
  "filament_notes": [
    ""
  ],
  "compatible_printers": [
    "Prusa MK4S 0.3 nozzle",
    "Prusa MK4S 0.4 nozzle",
    "Prusa MK4S 0.5 nozzle",
    "Prusa MK4S HF0.4 nozzle",
    "Prusa MK4S HF0.5 nozzle"
  ],
  "default_filament_colour": "#008000",
  "name": "Prusa Generic TPU @MK4S"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:53