Prusa Generic TPU HF @MINIIS

Volumic · FLEX · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Prusa Generic TPU HF @MINIIS

Compatible printers (3)

Prusa MINIIS 0.4 nozzle
Prusa MINIIS 0.6 nozzle
Prusa MINIIS 0.8 nozzle

Settings

Basic information

Material variant: FLEX overridden
was TPU (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 35 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 210 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 100 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 overridden
was 100 (inherited)
Slow down if layer below (sec): 4 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 5 (inherited)

Flow

Flow ratio: 1.15 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 3 overridden
was nil (inherited)
Retraction speed (mm/s): 40 overridden
was nil (inherited)
Deretraction speed (mm/s): 16 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	50 overridden was 40	50 overridden was 40
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa MINIIS 0.4 nozzle, Prusa MINIIS 0.6 nozzle, Prusa MINIIS 0.8 nozzle overridden
enable overhang bridge fan: 1 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: 6 overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: 1 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 50 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 50% (inherited)
pressure advance: 0 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: GFSA04 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "35"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "1.15"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "3"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "16"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "6"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "pressure_advance": [
    "0"
  ],
  "compatible_printers": [
    "Prusa MINIIS 0.4 nozzle",
    "Prusa MINIIS 0.6 nozzle",
    "Prusa MINIIS 0.8 nozzle"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "name": "Prusa Generic TPU HF @MINIIS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:53