Generic PETG @Elegoo

Generic · PETG · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Generic PETG @Elegoo

Compatible printers (13)

Elegoo Neptune 0.4 nozzle
Elegoo Neptune 2 0.4 nozzle
Elegoo Neptune 2D 0.4 nozzle
Elegoo Neptune 2S 0.4 nozzle
Elegoo Neptune 3 0.4 nozzle
Elegoo Neptune 3 Max 0.4 nozzle
Elegoo Neptune 3 Plus 0.4 nozzle
Elegoo Neptune 3 Pro 0.4 nozzle
Elegoo Neptune 4 0.4 nozzle
Elegoo Neptune 4 Max 0.4 nozzle
Elegoo Neptune 4 Plus 0.4 nozzle
Elegoo Neptune 4 Pro 0.4 nozzle
Elegoo Neptune X 0.4 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 20 (inherited)
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	80 inherited	80 inherited

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Elegoo Neptune 0.4 nozzle, Elegoo Neptune X 0.4 nozzle, Elegoo Neptune 2 0.4 nozzle, Elegoo Neptune 2S 0.4 nozzle, Elegoo Neptune 2D 0.4 nozzle, Elegoo Neptune 3 0.4 nozzle, Elegoo Neptune 3 0.4 nozzle, Elegoo Neptune 3 Pro 0.4 nozzle, Elegoo Neptune 3 Plus 0.4 nozzle, Elegoo Neptune 3 Max 0.4 nozzle, Elegoo Neptune 4 0.4 nozzle, Elegoo Neptune 4 Pro 0.4 nozzle, Elegoo Neptune 4 Plus 0.4 nozzle, Elegoo Neptune 4 Max 0.4 nozzle overridden
filament id: GFG99 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 overridden
was 100 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSG99_Elegoo_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSG99_Elegoo_00",
  "filament_id": "GFG99",
  "compatible_printers": [
    "Elegoo Neptune 0.4 nozzle",
    "Elegoo Neptune X 0.4 nozzle",
    "Elegoo Neptune 2 0.4 nozzle",
    "Elegoo Neptune 2S 0.4 nozzle",
    "Elegoo Neptune 2D 0.4 nozzle",
    "Elegoo Neptune 3 0.4 nozzle",
    "Elegoo Neptune 3 0.4 nozzle",
    "Elegoo Neptune 3 Pro 0.4 nozzle",
    "Elegoo Neptune 3 Plus 0.4 nozzle",
    "Elegoo Neptune 3 Max 0.4 nozzle",
    "Elegoo Neptune 4 0.4 nozzle",
    "Elegoo Neptune 4 Pro 0.4 nozzle",
    "Elegoo Neptune 4 Plus 0.4 nozzle",
    "Elegoo Neptune 4 Max 0.4 nozzle"
  ],
  "name": "Generic PETG @Elegoo"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:14