Flashforge Generic HIPS @G3U 0.6 Nozzle

Volumic · HIPS · 0.60mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Flashforge Generic ABS

→

Flashforge Generic HIPS @G3U 0.6 Nozzle

Compatible printers (1)

Flashforge Guider 3 Ultra 0.6 Nozzle

Settings

Basic information

Material variant: HIPS overridden
was ABS (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 overridden
was 1.04 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 18 (inherited)
Fan maximum (%): 50 overridden
was 60 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 15 overridden
was 5 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 12 overridden
was 20 (inherited)

Flow

Flow ratio: 1.01 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Guider 3 Ultra 0.6 Nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
enable pressure advance: 1 inherited
filament id: GFB99 overridden
was GFB99 (inherited)
filament minimal purge on wipe tower: 5 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unloading speed: 35 overridden
filament unloading speed start: 40 overridden
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 250 overridden
was 280 (inherited)
nozzle temperature range low: 220 overridden
was 240 (inherited)
overhang fan speed: 50 overridden
was 40 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.04 inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 40 overridden
was 80 (inherited)
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "HIPS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.05"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "1.01"
  ],
  "slow_down_min_speed": [
    "12"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    "Flashforge Generic HIPS @G3U 0.6 Nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "5"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.04"
  ],
  "compatible_printers": [
    "Flashforge Guider 3 Ultra 0.6 Nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "40"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "name": "Flashforge Generic HIPS @G3U 0.6 Nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:53