Generic TPU @Creality

Generic · TPU · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Generic TPU @Creality

Compatible printers (24)

Creality CR-10 Max 0.4 nozzle
Creality CR-10 V2 0.4 nozzle
Creality Ender-3 S1 0.4 nozzle
Creality Ender-3 S1 Pro 0.4 nozzle
Creality Ender-3 V2 0.4 nozzle
Creality Ender-3 V3 0.4 nozzle
Creality Ender-3 V3 0.6 nozzle
Creality Ender-3 V3 KE 0.4 nozzle
Creality Ender-3 V3 Plus 0.4 nozzle
Creality Ender-3 V3 Plus 0.6 nozzle
Creality Ender-5 0.4 nozzle
Creality Ender-5 Plus 0.4 nozzle
Creality Ender-5S 0.4 nozzle
Creality Ender-5 S1 0.4 nozzle
Creality Ender-6 0.4 nozzle
Creality K1 0.4 nozzle
Creality K1 0.6 nozzle
Creality K1 0.8 nozzle
Creality K1C 0.4 nozzle
Creality K1C 0.6 nozzle
Creality K1C 0.8 nozzle
Creality K1 Max 0.4 nozzle
Creality K1 Max 0.6 nozzle
Creality K1 Max 0.8 nozzle

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 3.2 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 0.4 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 inherited	30 inherited
Engineering Plate	30 inherited	30 inherited
High Temp Plate	35 inherited	35 inherited

Other settings

additional cooling fan speed: 70 inherited
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
compatible printers: Creality CR-10 V2 0.4 nozzle, Creality CR-10 Max 0.4 nozzle, Creality Ender-3 V2 0.4 nozzle, Creality Ender-3 S1 0.4 nozzle, Creality Ender-3 S1 Pro 0.4 nozzle, Creality Ender-3 V3 0.4 nozzle, Creality Ender-3 V3 0.6 nozzle, Creality Ender-3 V3 KE 0.4 nozzle, Creality Ender-3 V3 Plus 0.4 nozzle, Creality Ender-3 V3 Plus 0.6 nozzle, Creality Ender-5 0.4 nozzle, Creality Ender-5 Plus 0.4 nozzle, Creality Ender-5S 0.4 nozzle, Creality Ender-5 S1 0.4 nozzle, Creality Ender-6 0.4 nozzle, Creality K1 0.4 nozzle, Creality K1 0.6 nozzle, Creality K1 0.8 nozzle, Creality K1 Max 0.4 nozzle, Creality K1 Max 0.6 nozzle, Creality K1 Max 0.8 nozzle, Creality K1C 0.4 nozzle, Creality K1C 0.6 nozzle, Creality K1C 0.8 nozzle overridden
filament id: GFU99 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 200 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFU99_CREALITY_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "30"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "30"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "3.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFU99_CREALITY_00",
  "filament_id": "GFU99",
  "compatible_printers": [
    "Creality CR-10 V2 0.4 nozzle",
    "Creality CR-10 Max 0.4 nozzle",
    "Creality Ender-3 V2 0.4 nozzle",
    "Creality Ender-3 S1 0.4 nozzle",
    "Creality Ender-3 S1 Pro 0.4 nozzle",
    "Creality Ender-3 V3 0.4 nozzle",
    "Creality Ender-3 V3 0.6 nozzle",
    "Creality Ender-3 V3 KE 0.4 nozzle",
    "Creality Ender-3 V3 Plus 0.4 nozzle",
    "Creality Ender-3 V3 Plus 0.6 nozzle",
    "Creality Ender-5 0.4 nozzle",
    "Creality Ender-5 Plus 0.4 nozzle",
    "Creality Ender-5S 0.4 nozzle",
    "Creality Ender-5 S1 0.4 nozzle",
    "Creality Ender-6 0.4 nozzle",
    "Creality K1 0.4 nozzle",
    "Creality K1 0.6 nozzle",
    "Creality K1 0.8 nozzle",
    "Creality K1 Max 0.4 nozzle",
    "Creality K1 Max 0.6 nozzle",
    "Creality K1 Max 0.8 nozzle",
    "Creality K1C 0.4 nozzle",
    "Creality K1C 0.6 nozzle",
    "Creality K1C 0.8 nozzle"
  ],
  "name": "Generic TPU @Creality"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:14