Flashforge ABS Basic @FF G4P

Volumic · ABS · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Flashforge Generic ABS

→

Flashforge ABS Basic @FF G4P

Compatible printers (1)

Flashforge Guider4 Pro 0.4 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 250 inherited
Chamber (°C): 60 overridden

Cooling

Fan minimum (%): 18 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 4 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 15 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 105	0 overridden was 105
Engineering Plate	100 overridden was 105	100 overridden was 105
High Temp Plate	100 overridden was 105	100 overridden was 105
Textured PEI Plate	100 overridden was 105	100 overridden was 105

Other settings

activate chamber temp control: 1 overridden
additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.4 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
complete print exhaust fan speed: 50 overridden
during print exhaust fan speed: 40 overridden
enable pressure advance: 1 inherited
filament id: GFB99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 40 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.04 inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 80 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "18"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "40"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    "Flashforge ABS Basic @FF G4P"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material: ABS\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.04"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.4 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "80"
  ],
  "chamber_temperature": [
    "60"
  ],
  "activate_chamber_temp_control": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "50"
  ],
  "name": "Flashforge ABS Basic @FF G4P"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:53