Generic PETG-CF10 @Flashforge AD4

Generic · PETG-CF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG-CF10

→

Generic PETG-CF10 @Flashforge AD4

Compatible printers (3)

Flashforge Adventurer 4 Series 0.3 Nozzle
Flashforge Adventurer 4 Series 0.4 Nozzle
Flashforge Adventurer 4 Series 0.6 Nozzle

Settings

Basic information

Material variant: PETG-CF overridden
was PETG-CF (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 30 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 overridden
was 245 (inherited)
Nozzle (other layers) (°C): 255 overridden
was 245 (inherited)
Chamber (°C): 0 overridden
was 0 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 80 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 30 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 20 (inherited)

Flow

Flow ratio: 1.138 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 60	60 overridden was 60
Engineering Plate	60 overridden was 60	60 overridden was 60
High Temp Plate	80 overridden was 70	80 overridden was 70
Textured PEI Plate	60 overridden was 60	60 overridden was 60

Other settings

additional cooling fan speed: 100 overridden
was 100 (inherited)
bed temperature difference: 10 overridden
was 10 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 4 Series 0.3 Nozzle, Flashforge Adventurer 4 Series 0.4 Nozzle, Flashforge Adventurer 4 Series 0.6 Nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle (inherited)
enable overhang bridge fan: 1 overridden
was 1 (inherited)
enable pressure advance: 1 overridden
was 1 (inherited)
filament id: GFG99 overridden
was GFG99 (inherited)
filament is support: 0 overridden
was 0 (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil overridden
was nil (inherited)
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
was 100% (inherited)
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 260 overridden
was 260 (inherited)
nozzle temperature range low: 220 overridden
was 220 (inherited)
overhang fan speed: 90 overridden
was 90 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
pressure advance: 0.035 overridden
was 0.035 (inherited)
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
was 0 (inherited)
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: 100 overridden
was 100 (inherited)
temperature vitrification: 70 overridden
was 70 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "1.138"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Flashforge PETG-CF10"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PETG-CF10\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.035"
  ],
  "compatible_prints": [],
  "chamber_temperature": "0",
  "compatible_printers": [
    "Flashforge Adventurer 4 Series 0.3 Nozzle",
    "Flashforge Adventurer 4 Series 0.4 Nozzle",
    "Flashforge Adventurer 4 Series 0.6 Nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "compatible_prints_condition": "",
  "additional_cooling_fan_speed": [
    "100"
  ],
  "compatible_printers_condition": "",
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Generic PETG-CF10 @Flashforge AD4"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:52