Flashforge PETG-CF

Generic · PETG-CF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG-CF10

→

Flashforge PETG-CF

Compatible printers (9)

Flashforge AD5X 0.4 nozzle
Flashforge AD5X 0.6 nozzle
Flashforge AD5X 0.8 nozzle
Flashforge Adventurer 5M 0.4 Nozzle
Flashforge Adventurer 5M 0.6 Nozzle
Flashforge Adventurer 5M 0.8 Nozzle
Flashforge Adventurer 5M Pro 0.4 Nozzle
Flashforge Adventurer 5M Pro 0.6 Nozzle
Flashforge Adventurer 5M Pro 0.8 Nozzle

Settings

Basic information

Material variant: PETG-CF inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 245 inherited
Nozzle (other layers) (°C): 245 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 80 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	60 inherited	60 inherited

Other settings

additional cooling fan speed: 100 inherited
bed temperature difference: 10 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle (inherited)
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament id: GFG99 inherited
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 260 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.035 inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Flashforge PETG-CF"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PETG-CF10\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.035"
  ],
  "compatible_prints": [],
  "chamber_temperature": "0",
  "compatible_printers": [
    "Flashforge Adventurer 5M 0.4 Nozzle",
    "Flashforge Adventurer 5M 0.6 Nozzle",
    "Flashforge Adventurer 5M 0.8 Nozzle",
    "Flashforge Adventurer 5M Pro 0.4 Nozzle",
    "Flashforge Adventurer 5M Pro 0.6 Nozzle",
    "Flashforge Adventurer 5M Pro 0.8 Nozzle",
    "Flashforge AD5X 0.4 nozzle",
    "Flashforge AD5X 0.6 nozzle",
    "Flashforge AD5X 0.8 nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "compatible_prints_condition": "",
  "additional_cooling_fan_speed": [
    "100"
  ],
  "compatible_printers_condition": "",
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Flashforge PETG-CF"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:52