Volumic PP Ultra (Performance)

Volumic · PP · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pp

→

Volumic PP Ultra (Performance)

Compatible printers (15)

EXO42 IDRE (0.4 nozzle)
EXO42 IDRE COPY MODE (0.4 nozzle)
EXO42 IDRE MIRROR MODE (0.4 nozzle)
EXO42 Performance (0.4 nozzle)
EXO65 IDRE (0.4 nozzle)
EXO65 IDRE COPY MODE (0.4 nozzle)
EXO65 IDRE MIRROR MODE (0.4 nozzle)
EXO65 Performance (0.4 nozzle)
EXO65 Performance (0.6 nozzle)
EXO65 Performance (0.8 nozzle)
SH65 IDRE (0.4 nozzle)
SH65 IDRE COPY MODE (0.4 nozzle)
SH65 IDRE MIRROR MODE (0.4 nozzle)
SH65 Performance (0.4 nozzle)
VS30SC2 Performance (0.4 nozzle)

Settings

Basic information

Material variant: PP inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.92 inherited
Cost (/kg): 37.50 inherited

Print temperature

Nozzle (initial layer) (°C): 205 overridden
was 225 (inherited)
Nozzle (other layers) (°C): 205 overridden
was 225 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1.0 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 22 overridden
was 30 (inherited)

Retraction

Retraction length (mm): 3 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	90 inherited	90 inherited
Engineering Plate	90 inherited	90 inherited
High Temp Plate	90 overridden was 90	70 overridden was 90
Textured PEI Plate	90 inherited	90 inherited

Other settings

bed type: Cool Plate inherited
compatible printers: EXO42 Performance (0.4 nozzle), EXO65 Performance (0.4 nozzle), EXO65 Performance (0.6 nozzle), EXO65 Performance (0.8 nozzle), SH65 Performance (0.4 nozzle), EXO42 IDRE (0.4 nozzle), EXO42 IDRE COPY MODE (0.4 nozzle), EXO42 IDRE MIRROR MODE (0.4 nozzle), EXO65 IDRE (0.4 nozzle), EXO65 IDRE COPY MODE (0.4 nozzle), EXO65 IDRE MIRROR MODE (0.4 nozzle), SH65 IDRE (0.4 nozzle), SH65 IDRE COPY MODE (0.4 nozzle), SH65 IDRE MIRROR MODE (0.4 nozzle), VS30SC2 Performance (0.4 nozzle) overridden
filament id: GFB99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
internal bridge fan speed: 100 overridden
nozzle temperature range high: 225 overridden
nozzle temperature range low: 200 overridden
overhang fan speed: 100 overridden
was 80 (inherited)
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 overridden
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "37.50"
  ],
  "filament_type": [
    "PP"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "90"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "0.92"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "205"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1.0"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "3"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "90"
  ],
  "filament_max_volumetric_speed": [
    "22"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "205"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "compatible_printers": [
    "EXO42 Performance (0.4 nozzle)",
    "EXO65 Performance (0.4 nozzle)",
    "EXO65 Performance (0.6 nozzle)",
    "EXO65 Performance (0.8 nozzle)",
    "SH65 Performance (0.4 nozzle)",
    "EXO42 IDRE (0.4 nozzle)",
    "EXO42 IDRE COPY MODE (0.4 nozzle)",
    "EXO42 IDRE MIRROR MODE (0.4 nozzle)",
    "EXO65 IDRE (0.4 nozzle)",
    "EXO65 IDRE COPY MODE (0.4 nozzle)",
    "EXO65 IDRE MIRROR MODE (0.4 nozzle)",
    "SH65 IDRE (0.4 nozzle)",
    "SH65 IDRE COPY MODE (0.4 nozzle)",
    "SH65 IDRE MIRROR MODE (0.4 nozzle)",
    "VS30SC2 Performance (0.4 nozzle)"
  ],
  "internal_bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "225"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Volumic PP Ultra (Performance)"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:52