Generic PA @Geeetech

QIDI · PA · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Generic PA @Geeetech

Compatible printers (35)

Geeetech A10 M 0.4 nozzle
Geeetech A10 Pro 0.2 nozzle
Geeetech A10 Pro 0.4 nozzle
Geeetech A10 Pro 0.6 nozzle
Geeetech A10 Pro 0.8 nozzle
Geeetech A10 T 0.4 nozzle
Geeetech A20 0.2 nozzle
Geeetech A20 0.4 nozzle
Geeetech A20 0.6 nozzle
Geeetech A20 0.8 nozzle
Geeetech A20 M 0.4 nozzle
Geeetech A20 T 0.4 nozzle
Geeetech A30 M 0.4 nozzle
Geeetech A30 Pro 0.2 nozzle
Geeetech A30 Pro 0.4 nozzle
Geeetech A30 Pro 0.6 nozzle
Geeetech A30 Pro 0.8 nozzle
Geeetech A30 T 0.4 nozzle
Geeetech Mizar 0.2 nozzle
Geeetech Mizar 0.4 nozzle
Geeetech Mizar 0.6 nozzle
Geeetech Mizar 0.8 nozzle
Geeetech Mizar M 0.4 nozzle
Geeetech Mizar Max 0.2 nozzle
Geeetech Mizar Max 0.4 nozzle
Geeetech Mizar Max 0.6 nozzle
Geeetech Mizar Max 0.8 nozzle
Geeetech Mizar Pro 0.2 nozzle
Geeetech Mizar Pro 0.4 nozzle
Geeetech Mizar Pro 0.6 nozzle
Geeetech Mizar Pro 0.8 nozzle
Geeetech Mizar S 0.2 nozzle
Geeetech Mizar S 0.4 nozzle
Geeetech Mizar S 0.6 nozzle
Geeetech Mizar S 0.8 nozzle

Settings

Basic information

Material variant: PA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 280 overridden
was 290 (inherited)
Nozzle (other layers) (°C): 280 overridden
was 290 (inherited)

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 4 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 overridden
was 8 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	95 inherited	95 inherited
High Temp Plate	95 inherited	95 inherited

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Geeetech A10 Pro 0.2 nozzle, Geeetech A10 Pro 0.4 nozzle, Geeetech A10 Pro 0.6 nozzle, Geeetech A10 Pro 0.8 nozzle, Geeetech A20 0.2 nozzle, Geeetech A20 0.4 nozzle, Geeetech A20 0.6 nozzle, Geeetech A20 0.8 nozzle, Geeetech A30 Pro 0.2 nozzle, Geeetech A30 Pro 0.4 nozzle, Geeetech A30 Pro 0.6 nozzle, Geeetech A30 Pro 0.8 nozzle, Geeetech A10 M 0.4 nozzle, Geeetech A20 M 0.4 nozzle, Geeetech A30 M 0.4 nozzle, Geeetech A10 T 0.4 nozzle, Geeetech A20 T 0.4 nozzle, Geeetech A30 T 0.4 nozzle, Geeetech Mizar 0.2 nozzle, Geeetech Mizar 0.4 nozzle, Geeetech Mizar 0.6 nozzle, Geeetech Mizar 0.8 nozzle, Geeetech Mizar S 0.2 nozzle, Geeetech Mizar S 0.4 nozzle, Geeetech Mizar S 0.6 nozzle, Geeetech Mizar S 0.8 nozzle, Geeetech Mizar Pro 0.2 nozzle, Geeetech Mizar Pro 0.4 nozzle, Geeetech Mizar Pro 0.6 nozzle, Geeetech Mizar Pro 0.8 nozzle, Geeetech Mizar Max 0.2 nozzle, Geeetech Mizar Max 0.4 nozzle, Geeetech Mizar Max 0.6 nozzle, Geeetech Mizar Max 0.8 nozzle, Geeetech Mizar M 0.4 nozzle overridden
filament id: GFN99 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 270 inherited
overhang fan speed: 30 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 0 inherited
required nozzle HRC: 3 inherited
setting id: GFSN99_Geeetech_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 108 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "95"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "4"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "95"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "95"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "270"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "setting_id": "GFSN99_Geeetech_00",
  "filament_id": "GFN99",
  "compatible_printers": [
    "Geeetech A10 Pro 0.2 nozzle",
    "Geeetech A10 Pro 0.4 nozzle",
    "Geeetech A10 Pro 0.6 nozzle",
    "Geeetech A10 Pro 0.8 nozzle",
    "Geeetech A20 0.2 nozzle",
    "Geeetech A20 0.4 nozzle",
    "Geeetech A20 0.6 nozzle",
    "Geeetech A20 0.8 nozzle",
    "Geeetech A30 Pro 0.2 nozzle",
    "Geeetech A30 Pro 0.4 nozzle",
    "Geeetech A30 Pro 0.6 nozzle",
    "Geeetech A30 Pro 0.8 nozzle",
    "Geeetech A10 M 0.4 nozzle",
    "Geeetech A20 M 0.4 nozzle",
    "Geeetech A30 M 0.4 nozzle",
    "Geeetech A10 T 0.4 nozzle",
    "Geeetech A20 T 0.4 nozzle",
    "Geeetech A30 T 0.4 nozzle",
    "Geeetech Mizar 0.2 nozzle",
    "Geeetech Mizar 0.4 nozzle",
    "Geeetech Mizar 0.6 nozzle",
    "Geeetech Mizar 0.8 nozzle",
    "Geeetech Mizar S 0.2 nozzle",
    "Geeetech Mizar S 0.4 nozzle",
    "Geeetech Mizar S 0.6 nozzle",
    "Geeetech Mizar S 0.8 nozzle",
    "Geeetech Mizar Pro 0.2 nozzle",
    "Geeetech Mizar Pro 0.4 nozzle",
    "Geeetech Mizar Pro 0.6 nozzle",
    "Geeetech Mizar Pro 0.8 nozzle",
    "Geeetech Mizar Max 0.2 nozzle",
    "Geeetech Mizar Max 0.4 nozzle",
    "Geeetech Mizar Max 0.6 nozzle",
    "Geeetech Mizar Max 0.8 nozzle",
    "Geeetech Mizar M 0.4 nozzle"
  ],
  "name": "Generic PA @Geeetech"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:14