COEX TPE 60D @System

COEX 3D · TPU · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

COEX TPE 60D @base

→

COEX TPE 60D @System

Settings

Basic information

Material variant: TPU inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.20 inherited
Cost (/kg): 80.00 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 80 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 6.5 overridden
was 6.5 (inherited)

Retraction

Retraction length (mm): 0.4 inherited
Retraction speed (mm/s): 20 inherited
Deretraction speed (mm/s): 20 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature: 30 inherited
bed temperature initial layer: 35 inherited
bed type: Cool Plate inherited
disable fan first layers: 1 inherited
enable pressure advance: 0 inherited
filament id: CX60DB19 inherited
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: Flexible filament - print slowly with minimal retraction inherited
filament retract before wipe: 0% inherited
filament retract layer change: 0 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 0 inherited
filament retraction distances when cut: nil overridden
filament retraction minimum travel: 3 inherited
filament soluble: 0 inherited
filament wipe: 0 inherited
filament wipe distance: 0 inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 2 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: C0X60D19 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "80.00"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.20"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "0"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "20"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "20"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "0%"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "6.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "CX60DB19",
  "filament_notes": "Flexible filament - print slowly with minimal retraction",
  "bed_temperature": [
    "30"
  ],
  "compatible_prints": [],
  "compatible_printers": [],
  "enable_pressure_advance": [
    "0"
  ],
  "disable_fan_first_layers": [
    "1"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "35"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "0"
  ],
  "setting_id": "C0X60D19",
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "COEX TPE 60D @System"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:50