QIDI PETG Tough @Qidi Q1 Pro 0.8 nozzle

Generic · PETG · 0.80mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

QIDI PETG Tough @Qidi

→

QIDI PETG Tough @Qidi Q1 Pro 0.8 nozzle

Compatible printers (1)

Qidi Q1 Pro 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 40 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 13 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	80 inherited	80 inherited

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Qidi Q1 Pro 0.8 nozzle overridden
was Qidi X-Plus 0.4 nozzle, Qidi X-Max 0.4 nozzle, Qidi X-CF Pro 0.4 nozzle, Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle, Qidi X-Smart 3 0.6 nozzle, Qidi X-Plus 3 0.6 nozzle, Qidi X-Max 3 0.6 nozzle, Qidi X-Smart 3 0.8 nozzle, Qidi X-Plus 3 0.8 nozzle, Qidi X-Max 3 0.8 nozzle (inherited)
enable pressure advance: 1 inherited
filament id: GFT01 overridden
was GFT01 (inherited)
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 260 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
pressure advance: 0.024 overridden
was 0.04 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFST01_Qidi_08 overridden
was GFST01_Qidi_04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "13"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFST01_Qidi_08",
  "filament_id": "GFT01",
  "pressure_advance": [
    "0.024"
  ],
  "compatible_printers": [
    "Qidi Q1 Pro 0.8 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "QIDI PETG Tough @Qidi Q1 Pro 0.8 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:14