Snapmaker TPE

Generic · TPU · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Snapmaker TPU @base

→

Snapmaker TPE

Compatible printers (24)

Snapmaker A250 (0.4 nozzle)
Snapmaker A250 (0.6 nozzle)
Snapmaker A250 (0.8 nozzle)
Snapmaker A250 BKit (0.4 nozzle)
Snapmaker A250 BKit (0.6 nozzle)
Snapmaker A250 BKit (0.8 nozzle)
Snapmaker A250 QS+B Kit (0.4 nozzle)
Snapmaker A250 QS+B Kit (0.6 nozzle)
Snapmaker A250 QS+B Kit (0.8 nozzle)
Snapmaker A250 QSKit (0.4 nozzle)
Snapmaker A250 QSKit (0.6 nozzle)
Snapmaker A250 QSKit (0.8 nozzle)
Snapmaker A350 (0.4 nozzle)
Snapmaker A350 (0.6 nozzle)
Snapmaker A350 (0.8 nozzle)
Snapmaker A350 BKit (0.4 nozzle)
Snapmaker A350 BKit (0.6 nozzle)
Snapmaker A350 BKit (0.8 nozzle)
Snapmaker A350 QS+B Kit (0.4 nozzle)
Snapmaker A350 QS+B Kit (0.6 nozzle)
Snapmaker A350 QS+B Kit (0.8 nozzle)
Snapmaker A350 QSKit (0.4 nozzle)
Snapmaker A350 QSKit (0.6 nozzle)
Snapmaker A350 QSKit (0.8 nozzle)

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 overridden
was 1.24 (inherited)
Cost (/kg): 35 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 7.2 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	45 overridden was 40
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Snapmaker A250 (0.4 nozzle), Snapmaker A250 (0.6 nozzle), Snapmaker A250 (0.8 nozzle), Snapmaker A250 BKit (0.4 nozzle), Snapmaker A250 BKit (0.6 nozzle), Snapmaker A250 BKit (0.8 nozzle), Snapmaker A250 QS+B Kit (0.4 nozzle), Snapmaker A250 QS+B Kit (0.6 nozzle), Snapmaker A250 QS+B Kit (0.8 nozzle), Snapmaker A250 QSKit (0.4 nozzle), Snapmaker A250 QSKit (0.6 nozzle), Snapmaker A250 QSKit (0.8 nozzle), Snapmaker A350 (0.4 nozzle), Snapmaker A350 (0.6 nozzle), Snapmaker A350 (0.8 nozzle), Snapmaker A350 BKit (0.4 nozzle), Snapmaker A350 BKit (0.6 nozzle), Snapmaker A350 BKit (0.8 nozzle), Snapmaker A350 QS+B Kit (0.4 nozzle), Snapmaker A350 QS+B Kit (0.6 nozzle), Snapmaker A350 QS+B Kit (0.8 nozzle), Snapmaker A350 QSKit (0.4 nozzle), Snapmaker A350 QSKit (0.6 nozzle), Snapmaker A350 QSKit (0.8 nozzle) overridden
filament id: 1480063856 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: eSUN eLastic TPE-83A overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: 2302237917 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "35"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "45"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "7.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "1480063856",
  "setting_id": "2302237917",
  "filament_notes": [
    "eSUN eLastic TPE-83A\n"
  ],
  "compatible_printers": [
    "Snapmaker A250 (0.4 nozzle)",
    "Snapmaker A250 (0.6 nozzle)",
    "Snapmaker A250 (0.8 nozzle)",
    "Snapmaker A250 BKit (0.4 nozzle)",
    "Snapmaker A250 BKit (0.6 nozzle)",
    "Snapmaker A250 BKit (0.8 nozzle)",
    "Snapmaker A250 QS+B Kit (0.4 nozzle)",
    "Snapmaker A250 QS+B Kit (0.6 nozzle)",
    "Snapmaker A250 QS+B Kit (0.8 nozzle)",
    "Snapmaker A250 QSKit (0.4 nozzle)",
    "Snapmaker A250 QSKit (0.6 nozzle)",
    "Snapmaker A250 QSKit (0.8 nozzle)",
    "Snapmaker A350 (0.4 nozzle)",
    "Snapmaker A350 (0.6 nozzle)",
    "Snapmaker A350 (0.8 nozzle)",
    "Snapmaker A350 BKit (0.4 nozzle)",
    "Snapmaker A350 BKit (0.6 nozzle)",
    "Snapmaker A350 BKit (0.8 nozzle)",
    "Snapmaker A350 QS+B Kit (0.4 nozzle)",
    "Snapmaker A350 QS+B Kit (0.6 nozzle)",
    "Snapmaker A350 QS+B Kit (0.8 nozzle)",
    "Snapmaker A350 QSKit (0.4 nozzle)",
    "Snapmaker A350 QSKit (0.6 nozzle)",
    "Snapmaker A350 QSKit (0.8 nozzle)"
  ],
  "default_filament_colour": [
    ""
  ],
  "name": "Snapmaker TPE"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:47