Bambu Support For PLA @BBL H2C

Bambu Lab · PLA · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Bambu Support For PLA @base

→

Bambu Support For PLA @BBL H2C

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (2)

Bambu Lab H2C 0.6 nozzle
Bambu Lab H2C 0.8 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.30 inherited
Cost (/kg): 69.98 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 100 (inherited)
Fan maximum (%): 30 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 6 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil via fdm_filament_template_direct_dual
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	55 overridden was 0	55 overridden was 0
High Temp Plate	60 inherited	60 inherited
Cool Plate SuperTack	40 overridden	40 overridden

Other settings

additional cooling fan speed: 70 inherited
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
compatible printers: Bambu Lab H2C 0.6 nozzle, Bambu Lab H2C 0.8 nozzle overridden
description: This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function. inherited
enable overhang bridge fan: 0 inherited
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament adhesiveness category: 702 inherited
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament change length: 4 overridden
filament change length nc: 4 overridden
filament cooling before tower: 10, 10 overridden
filament dev ams drying heat distortion temperature: 50 inherited
filament dev ams drying temperature: 60, 60, 50, 50 inherited
filament dev drying softening temperature: 55 inherited
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFS02 inherited
filament is support: 1 inherited
filament long retractions when cut: nil, nil via fdm_filament_template_direct_dual
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 0, 0 via fdm_filament_template_direct_dual
filament pre cooling temperature nc: 180, 180 overridden
filament prime volume: 30 overridden
filament prime volume nc: 30 overridden
filament ramming travel time: 0, 0 overridden
filament ramming travel time nc: 1, 1 overridden
filament ramming volumetric speed: -1, -1 via fdm_filament_template_direct_dual
filament ramming volumetric speed nc: -1, -1 via fdm_filament_template_direct_dual
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 18, 18 overridden
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: nil, nil via fdm_filament_template_direct_dual
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament wipe: nil, nil via fdm_filament_template_direct_dual
filament wipe distance: nil, nil via fdm_filament_template_direct_dual
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: nil, nil via fdm_filament_template_direct_dual
first x layer fan speed: 0 overridden
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1 via fdm_filament_template_direct_dual
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 10, 10 via fdm_filament_template_direct_dual
setting id: GFSS02_22 overridden
slow down for layer cooling: 0 inherited
temperature vitrification: 60 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "69.98"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "55"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.30"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220",
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1",
    "1"
  ],
  "filament_is_support": [
    "1"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "55"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "6",
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "220",
    "220"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "enable_overhang_bridge_fan": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "description": "This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.",
  "filament_id": "GFS02",
  "filament_adhesiveness_category": [
    "702"
  ],
  "filament_dev_ams_drying_temperature": [
    "60",
    "60",
    "50",
    "50"
  ],
  "filament_dev_drying_softening_temperature": [
    "55"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "50"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "18",
    "18"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "10",
    "10"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "1",
    "1"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "180",
    "180"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "setting_id": "GFSS02_22",
  "compatible_printers": [
    "Bambu Lab H2C 0.6 nozzle",
    "Bambu Lab H2C 0.8 nozzle"
  ],
  "supertack_plate_temp": [
    "40"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "filament_change_length": [
    "4"
  ],
  "first_x_layer_fan_speed": [
    "0"
  ],
  "filament_prime_volume_nc": [
    "30"
  ],
  "filament_change_length_nc": [
    "4"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "supertack_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Bambu Support For PLA @BBL H2C"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:17
v1 created 2026-05-19 04:01