Snapmaker TPU 95A @U1

Generic · TPU · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

Snapmaker TPU 95A @U1 base

→

Snapmaker TPU 95A @U1

Compatible printers (1)

Snapmaker U1 (0.4 nozzle)

Settings

Basic information

Material variant: TPU overridden
was TPU (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 20 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 225 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 225 overridden
was 240 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 70 overridden
was 100 (inherited)
Fan maximum (%): 70 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 3.2 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 1.4 overridden
was 0.4 (inherited)
Retraction speed (mm/s): 30 overridden
was nil (inherited)
Deretraction speed (mm/s): 8 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 overridden was 30	30 overridden was 30
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	30 overridden was 30	30 overridden was 30
High Temp Plate	55 overridden was 35	55 overridden was 35
Textured PEI Plate	35 overridden was 35	35 overridden was 35

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
adaptive pressure advance: 0 overridden
adaptive pressure advance bridges: 0 overridden
adaptive pressure advance model: 0,0,0 0,0,0 overridden
adaptive pressure advance overhangs: 0 overridden
additional cooling fan speed: 70 overridden
was 70 (inherited)
bed type: Cool Plate inherited
compatible printers: Snapmaker U1 (0.4 nozzle) overridden
complete print exhaust fan speed: 80 overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament id: 297165629001 inherited
filament is support: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament stamping distance: 0 overridden
filament stamping loading speed: 0 overridden
filament toolchange delay: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: Auto Lift overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 0 overridden
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 overridden
was 250 (inherited)
nozzle temperature range low: 200 overridden
was 200 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 95% overridden
was 95% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
setting id: 316428530 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "filament_id": "297165629001",
  "fan_max_speed": [
    "70"
  ],
  "fan_min_speed": [
    "70"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "30"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "225"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "35"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "Auto Lift"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "1.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "8"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "30"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "3.2"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "225"
  ],
  "textured_plate_temp_initial_layer": [
    "35"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "setting_id": "316428530",
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Snapmaker U1 (0.4 nozzle)"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Snapmaker TPU 95A @U1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:46