slicershare (test)
← Generic PVA @Qidi

History of Generic PVA @Qidi

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: fdm_filament_common → fdm_filament_pva
  1. via parent v13 of fdm_filament_common — updated
    2026-05-19 04:18
    Settings (2)
    • filament z hop types removed nil
    • slow down layer time 8 → 5
  2. via parent v10 of fdm_filament_pva — updated
    2026-05-19 04:18
    Settings (78)
    • activate air filtration removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  3. via parent v12 of fdm_filament_common — updated
    2026-05-19 04:18
    Settings (82)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  4. via parent v9 of fdm_filament_pva — updated
    2026-05-19 04:18
    Settings (88)
    • activate air filtration added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cool plate temp 45 → 35
    • cool plate temp initial layer 45 → 35
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament adhesiveness category removed 704
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature 75 → 45.0
    • filament dev ams drying temperature 65, 85, 65, 70 → 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time 12, 18, 12, 18 → 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature 40 → 35.0
    • filament dev drying softening temperature 75 → 40.0
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; filament start gcode
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • hot plate temp 55 → 45
    • hot plate temp initial layer 55 → 45
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 250
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • slow down min speed 50 → 10
    • supertack plate temp 35 → 45
    • supertack plate temp initial layer 35 → 45
    • temperature vitrification 45 → 50
    • textured plate temp 55 → 60
    • textured plate temp initial layer 55 → 60
    • volumetric speed coefficients added 0 0 0 0 0 0
  5. via parent v11 of fdm_filament_common — updated
    2026-05-19 04:17
    Settings (80)
    • activate air filtration added 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature added 45.0
    • filament dev ams drying temperature added 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time added 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature added 35.0
    • filament dev drying softening temperature added 40.0
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • volumetric speed coefficients added 0 0 0 0 0 0
  6. via parent v8 of fdm_filament_pva — updated
    2026-05-19 04:15
    Settings (20)
    • cool plate temp 35 → 45
    • cool plate temp initial layer 35 → 45
    • filament adhesiveness category added 704
    • filament dev ams drying heat distortion temperature added 75
    • filament dev ams drying temperature added 65, 85, 65, 70
    • filament dev ams drying time added 12, 18, 12, 18
    • filament dev drying cooling temperature added 40
    • filament dev drying softening temperature added 75
    • filament end gcode ; filament end gcode → ; filament end gcode
    • filament start gcode ; filament start gcode → ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • hot plate temp 45 → 55
    • hot plate temp initial layer 45 → 55
    • nozzle temperature range high removed 250
    • nozzle temperature range low removed 190
    • slow down min speed 10 → 50
    • supertack plate temp added 35
    • supertack plate temp initial layer added 35
    • temperature vitrification 50 → 45
    • textured plate temp 45 → 55
    • textured plate temp initial layer 45 → 55
  7. via parent v7 of fdm_filament_pva — updated
    2026-05-19 04:14
    Settings (2)
    • filament minimal purge on wipe tower 90 → 15
    • required nozzle HRC added 3
  8. via parent v10 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (2)
    • bed type removed Cool Plate
    • filament z hop types added nil
  9. via parent v9 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (5)
    • bed type added Cool Plate
    • filament is support added 0
    • filament minimal purge on wipe tower 90 → 15
    • filament z hop types removed nil
    • required nozzle HRC added 3
  10. via parent v6 of fdm_filament_pva — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (18)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • bed type removed Cool Plate
    • compatible printers removed —
    • cool plate temp 55 → 35
    • cool plate temp initial layer 55 → 35
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • filament end gcode added ; filament end gcode
    • filament minimal purge on wipe tower 15 → 90
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} → ; filament start gcode
    • filament vendor QIDI → Generic
    • hot plate temp 55 → 45
    • hot plate temp initial layer 55 → 45
    • nozzle temperature range high 240 → 250
    • temperature vitrification 55 → 50
    • textured plate temp 65 → 45
    • textured plate temp initial layer 65 → 45
  11. via parent v8 of fdm_filament_common — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (11)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • bed type removed Cool Plate
    • compatible printers removed —
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • filament end gcode added ; filament end gcode
    • filament minimal purge on wipe tower 15 → 90
    • filament start gcode added ; Filament gcode
    • filament vendor QIDI → Generic
    • reduce fan stop start freq 1 → 0
  12. via parent v5 of fdm_filament_pva — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (13)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • compatible printers added —
    • cool plate temp 35 → 55
    • cool plate temp initial layer 35 → 55
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • filament end gcode removed ; filament end gcode
    • filament start gcode ; Filament gcode → ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif}
    • filament vendor Generic → QIDI
    • required nozzle HRC removed 3
    • textured plate temp 55 → 65
    • textured plate temp initial layer 55 → 65
  13. via parent v7 of fdm_filament_common — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (11)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • compatible printers added —
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • filament end gcode removed ; filament end gcode
    • filament is support removed 0
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → QIDI
    • reduce fan stop start freq 0 → 1
    • required nozzle HRC removed 3
  14. direct edit v1 — created
    2026-05-19 04:14
    Profile created at this point. No prior version to diff against.
  15. via parent v4 of fdm_filament_pva — updated
    2026-05-19 04:14
    Settings (9)
    • bed type added Cool Plate
    • filament diameter 2.85 → 1.75
    • filament start gcode ; filament start gcode → ; Filament gcode
    • hot plate temp 45 → 55
    • hot plate temp initial layer 45 → 55
    • nozzle temperature range high 250 → 240
    • temperature vitrification 50 → 55
    • textured plate temp 45 → 55
    • textured plate temp initial layer 45 → 55
  16. via parent v6 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (2)
    • bed type added Cool Plate
    • filament diameter 2.85 → 1.75
  17. via parent v3 of fdm_filament_pva — updated
    2026-05-19 04:14
    Settings (79)
    • activate air filtration removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament diameter 1.75 → 2.85
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp 60 → 45
    • textured plate temp initial layer 60 → 45
    • volumetric speed coefficients removed 0 0 0 0 0 0
  18. via parent v5 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (4)
    • filament diameter 1.75 → 2.85
    • filament z hop types added nil
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  19. via parent v4 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (83)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • filament z hop types removed nil
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  20. via parent v2 of fdm_filament_pva — updated
    2026-05-19 04:14
    Settings (89)
    • activate air filtration added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cool plate temp 45 → 35
    • cool plate temp initial layer 45 → 35
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament adhesiveness category removed 704
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature 75 → 45.0
    • filament dev ams drying temperature 65, 85, 65, 70 → 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time 12, 18, 12, 18 → 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature 40 → 35.0
    • filament dev drying softening temperature 75 → 40.0
    • filament diameter 2.85 → 1.75
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; filament start gcode
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • hot plate temp 55 → 45
    • hot plate temp initial layer 55 → 45
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 250
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • slow down min speed 50 → 10
    • supertack plate temp 35 → 45
    • supertack plate temp initial layer 35 → 45
    • temperature vitrification 45 → 50
    • textured plate temp 55 → 60
    • textured plate temp initial layer 55 → 60
    • volumetric speed coefficients added 0 0 0 0 0 0
  21. via parent v3 of fdm_filament_common — updated
    2026-05-19 04:01
    Settings (81)
    • activate air filtration added 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature added 45.0
    • filament dev ams drying temperature added 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time added 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature added 35.0
    • filament dev drying softening temperature added 40.0
    • filament diameter 2.85 → 1.75
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • volumetric speed coefficients added 0 0 0 0 0 0
  22. via parent v1 of fdm_filament_pva — created
    2026-05-19 04:01
    Profile created at this point. No prior version to diff against.
  23. via parent v2 of fdm_filament_common — updated
    2026-05-19 04:01
    Settings (2)
    • bed type removed Cool Plate
    • filament diameter 1.75 → 2.85
  24. via parent v1 of fdm_filament_common — created
    2026-05-19 04:01
    Profile created at this point. No prior version to diff against.