PolyLite PETG @BBL X1C 0.2 nozzle

Polymaker · PETG · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

PolyLite PETG @base

→

PolyLite PETG @BBL X1C

→

PolyLite PETG @BBL X1C 0.2 nozzle

Compatible printers (4)

Bambu Lab P1S 0.2 nozzle
Bambu Lab X1 0.2 nozzle
Bambu Lab X1 Carbon 0.2 nozzle
Bambu Lab X1E 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Polymaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 255 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 40 inherited
Fan maximum (%): 90 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 1 overridden
was 11.5 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited

Other settings

bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.2 nozzle, Bambu Lab X1 0.2 nozzle, Bambu Lab P1S 0.2 nozzle, Bambu Lab X1E 0.2 nozzle overridden
was Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle (inherited)
filament adaptive volumetric speed: 0, 0 inherited
filament extruder variant: Direct Drive Standard, Direct Drive High Flow inherited
filament flush temp: 0, 0 inherited
filament flush volumetric speed: 0, 0 inherited
filament id: OGFG60 inherited
filament long retractions when cut: nil, nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0, 0 inherited
filament ramming travel time: 0, 0 inherited
filament ramming volumetric speed: -1, -1 inherited
filament retract before wipe: nil, nil inherited
filament retract restart extra: nil, nil inherited
filament retract when changing layer: nil, nil inherited
filament retraction distances when cut: nil, nil inherited
filament retraction minimum travel: nil, nil inherited
filament soluble: 0 inherited
filament wipe: nil, nil inherited
filament wipe distance: nil, nil inherited
filament z hop: nil, nil inherited
filament z hop types: nil, nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
long retractions when ec: 0, 0 inherited
nozzle temperature range high: 270 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
reduce fan stop start freq: 1 inherited
retraction distances when ec: 0, 0 inherited
setting id: GFSG60_01 overridden
was GFSG60_00 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255",
    "255"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95",
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "1",
    "1"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255",
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "OGFG60",
  "setting_id": "GFSG60_01",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.2 nozzle",
    "Bambu Lab X1 0.2 nozzle",
    "Bambu Lab P1S 0.2 nozzle",
    "Bambu Lab X1E 0.2 nozzle"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "name": "PolyLite PETG @BBL X1C 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:45