Fiberon PA12-CF @base

Polymaker · PA-CF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Fiberon PA12-CF @base

Inherited from this (3)

Settings

Basic information

Material variant: PA-CF overridden
was PA (inherited)
Vendor: Polymaker overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.06 overridden
was 1.04 (inherited)
Cost (/kg): 99.99 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 300 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 300 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 100 overridden
was 60 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 overridden
was 10 (inherited)
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 14 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	40 overridden was 100	40 overridden was 100
High Temp Plate	40 overridden was 100	40 overridden was 100
Textured PEI Plate	40 overridden was 100	40 overridden was 100

Other settings

bed type: Cool Plate inherited
filament id: OGFL52 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 2 overridden
was 0 (inherited)
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 260 overridden
was 260 (inherited)
overhang fan speed: 100 overridden
was 60 (inherited)
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 overridden
was 0 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 131 overridden
was 108 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "99.99"
  ],
  "filament_type": [
    "PA-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.06"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "300"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "131"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "14"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "300"
  ],
  "textured_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "OGFL52",
  "name": "Fiberon PA12-CF @base"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:51
v1 created 2026-05-19 04:44