QIDI ASA-Aero @Qidi

Generic · ASA · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

QIDI ASA-Aero @Qidi

Compatible printers (6)

Qidi X-CF Pro 0.4 nozzle
Qidi X-Max 0.4 nozzle
Qidi X-Max 3 0.4 nozzle
Qidi X-Plus 0.4 nozzle
Qidi X-Plus 3 0.4 nozzle
Qidi X-Smart 3 0.4 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.03 overridden
was 1.04 (inherited)
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 80 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.7 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): 0.01 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	90 overridden was 95	90 overridden was 95
Engineering Plate	90 overridden was 95	90 overridden was 95
High Temp Plate	90 overridden was 95	90 overridden was 95
Textured PEI Plate	90 overridden	90 overridden

Other settings

additional fan full speed layer: 0 inherited
chamber temperatures: 60 overridden
close additional fan first x layers: 3 inherited
compatible printers: Qidi X-Plus 0.4 nozzle, Qidi X-Max 0.4 nozzle, Qidi X-CF Pro 0.4 nozzle, Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFB01 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.021 overridden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSB01_Qidi_06 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "90"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.03"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.7"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "0.01"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "90"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSB01_Qidi_06",
  "filament_id": "GFB01",
  "pressure_advance": [
    "0.021"
  ],
  "compatible_printers": [
    "Qidi X-Plus 0.4 nozzle",
    "Qidi X-Max 0.4 nozzle",
    "Qidi X-CF Pro 0.4 nozzle",
    "Qidi X-Smart 3 0.4 nozzle",
    "Qidi X-Plus 3 0.4 nozzle",
    "Qidi X-Max 3 0.4 nozzle"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "name": "QIDI ASA-Aero @Qidi"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:14