Elegoo RAPID PETG @base

Elegoo · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_elegoo_filament_common

→

fdm_elegoo_filament_pet

→

Elegoo RAPID PETG @base

Inherited from this (5)

Settings

Basic information

Material variant: PETG overridden
was PET (inherited)
Vendor: Elegoo overridden
was Elegoo (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 overridden
was 1.27 (inherited)
Cost (/kg): 0 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 20 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 20 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 18 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	70 overridden was 0	70 overridden was 0
High Temp Plate	70 overridden was 80	70 overridden was 80
Textured PEI Plate	70 overridden was 80	70 overridden was 80

Other settings

activate air filtration: 0 inherited
chamber temperatures: 0 inherited
complete print exhaust fan speed: 70 inherited
during print exhaust fan speed: 70 inherited
filament id: ERPETGB00 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 overridden
was 260 (inherited)
nozzle temperature range low: 230 overridden
was 220 (inherited)
overhang fan speed: 90 overridden
was 100 (inherited)
overhang fan threshold: 10% overridden
was 95% (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Elegoo"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "compatible_printers": [],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "chamber_temperatures": [
    "0"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "ERPETGB00",
  "name": "Elegoo RAPID PETG @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:39