Creality Generic PLA @Ender-5Max-all

Generic · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

Creality Generic PLA @Ender-5Max-all

Compatible printers (1)

Creality Ender-5 Max 0.4 nozzle

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 overridden
was 0 (inherited)
Cost (/kg): 20 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 200 (inherited)
Chamber (°C): 35 overridden

Cooling

Fan minimum (%): 100 overridden
was 35 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 100 overridden
was 60 (inherited)
Slow down if layer below (sec): 5 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 0.9 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 40 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	45 overridden was 60	45 overridden was 60
Engineering Plate	50 overridden was 60	50 overridden was 60
High Temp Plate	45 overridden was 60	45 overridden was 60
Textured PEI Plate	45 overridden was 60	45 overridden was 60

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
compatible printers: Creality Ender-5 Max 0.4 nozzle overridden
complete print exhaust fan speed: 80 overridden
cool special cds fan speed: 0 overridden
default filament colour: "" overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament id: 04001 overridden
filament is support: 0 overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament notes: "" overridden
filament ramming parameters: "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6" overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: 0 overridden
filament retract lift below: 0 overridden
filament retract lift enforce: All Surfaces overridden
filament retract restart extra: 0 overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 240 overridden
nozzle temperature range low: 190 overridden
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
pressure advance: 0.03 overridden
reduce fan stop start freq: 1 overridden
was 0 (inherited)
required nozzle HRC: 0 overridden
setting id: GFSA04_CREALITY_00 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": "100",
  "fan_min_speed": "100",
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": "nil",
  "instantiation": "true",
  "eng_plate_temp": "50",
  "filament_z_hop": "nil",
  "hot_plate_temp": "45",
  "cool_plate_temp": "45",
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": "0",
  "filament_diameter": "1.75",
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": "220",
  "overhang_fan_speed": "100",
  "filament_flow_ratio": "0.9",
  "slow_down_min_speed": "10",
  "textured_plate_temp": "45",
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": "nil",
  "full_fan_speed_layer": "0",
  "slow_down_layer_time": "5",
  "fan_cooling_layer_time": "100",
  "filament_wipe_distance": "nil",
  "overhang_fan_threshold": "25%",
  "filament_retraction_speed": "nil",
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": "nil",
  "reduce_fan_stop_start_freq": "1",
  "filament_deretraction_speed": "nil",
  "slow_down_for_layer_cooling": "1",
  "close_fan_the_first_x_layers": "1",
  "eng_plate_temp_initial_layer": "50",
  "filament_retract_before_wipe": "nil",
  "hot_plate_temp_initial_layer": "45",
  "cool_plate_temp_initial_layer": "45",
  "filament_max_volumetric_speed": [
    "40"
  ],
  "filament_retract_restart_extra": "0",
  "nozzle_temperature_initial_layer": "220",
  "textured_plate_temp_initial_layer": "45",
  "filament_retraction_minimum_travel": "nil",
  "filament_minimal_purge_on_wipe_tower": "15",
  "filament_retract_when_changing_layer": "nil",
  "setting_id": "GFSA04_CREALITY_00",
  "filament_id": "04001",
  "filament_notes": "\"\"",
  "filament_shrink": "100%",
  "pressure_advance": "0.03",
  "filament_load_time": "0",
  "chamber_temperature": "35",
  "compatible_printers": [
    "Creality Ender-5 Max 0.4 nozzle"
  ],
  "filament_is_support": "0",
  "required_nozzle_HRC": "0",
  "filament_unload_time": "0",
  "filament_cooling_moves": "4",
  "filament_loading_speed": "28",
  "activate_air_filtration": "0",
  "default_filament_colour": "\"\"",
  "enable_pressure_advance": "1",
  "filament_unloading_speed": "90",
  "filament_toolchange_delay": "0",
  "cool_special_cds_fan_speed": "0",
  "enable_overhang_bridge_fan": "1",
  "filament_multitool_ramming": "0",
  "filament_ramming_parameters": "\"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6\"",
  "filament_retract_lift_above": "0",
  "filament_retract_lift_below": "0",
  "additional_cooling_fan_speed": "0",
  "filament_cooling_final_speed": "3.4",
  "filament_loading_speed_start": "3",
  "nozzle_temperature_range_low": "190",
  "activate_chamber_temp_control": "0",
  "filament_retract_lift_enforce": "All Surfaces",
  "nozzle_temperature_range_high": "240",
  "during_print_exhaust_fan_speed": "60",
  "filament_cooling_initial_speed": "2.2",
  "filament_unloading_speed_start": "100",
  "filament_multitool_ramming_flow": "10",
  "complete_print_exhaust_fan_speed": "80",
  "filament_multitool_ramming_volume": "10",
  "support_material_interface_fan_speed": "-1",
  "name": "Creality Generic PLA @Ender-5Max-all"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:38