3D-Fuel PCTG Pro @Bambu Lab X1E 0.4 nozzle

3D-Fuel · PCTG · 0.40mm nozzle · by root · 3 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Compatible printers (1)

Bambu Lab X1E 0.4 nozzle

Settings

Basic information

Material variant: PCTG overridden
Vendor: 3D-Fuel overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.23 overridden
Cost (/kg): 29.95 overridden

Print temperature

Nozzle (initial layer) (°C): 260 overridden
Nozzle (other layers) (°C): 260 overridden

Cooling

Fan minimum (%): 10 overridden
Fan maximum (%): 40 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 30 overridden
Slow down if layer below (sec): 12 overridden
Min speed when slowed (mm/s): 20 overridden

Flow

Flow ratio: 0.98 overridden
Max volumetric speed (mm³/s): 12 overridden

Retraction

Retraction length (mm): 0.4 overridden
Retraction speed (mm/s): nil overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden	0 overridden
Engineering Plate	80 overridden	80 overridden
High Temp Plate	80 overridden	80 overridden
Textured PEI Plate	80 overridden	80 overridden
Cool Plate SuperTack	0 overridden	0 overridden

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255
{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

filament_end_gcode overridden

; filament end gcode 
M106 P3 S0

Other settings

activate air filtration: 0 overridden
additional cooling fan speed: 0 overridden
additional fan full speed layer: 0 overridden
chamber temperatures: 45 overridden
circle compensation speed: 200 overridden
close additional fan first x layers: 3 overridden
compatible printers: Bambu Lab X1E 0.4 nozzle overridden
complete print exhaust fan speed: 70 overridden
cooling perimeter transition distance: 10 overridden
cooling slowdown logic: uniform_cooling overridden
counter coef 1: 0 overridden
counter coef 2: 0.025 overridden
counter coef 3: -0.11 overridden
counter limit max: 0.05 overridden
counter limit min: -0.04 overridden
diameter limit: 50 overridden
during print exhaust fan speed: 70 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 0 overridden
filament adaptive volumetric speed: 0 overridden
filament adhesiveness category: 300 overridden
filament bridge speed: 25 overridden
filament change length: 10 overridden
filament change length nc: 10 overridden
filament cooling before tower: 10 overridden
filament dev ams drying heat distortion temperature: 0 overridden
filament dev ams drying temperature: 0 overridden
filament dev ams drying time: 0 overridden
filament dev chamber drying bed temperature: 0 overridden
filament dev chamber drying time: 0 overridden
filament dev drying cooling temperature: 0 overridden
filament dev drying softening temperature: 0 overridden
filament enable overhang speed: 1 overridden
filament extruder compatibility: 0 overridden
filament extruder variant: Direct Drive Standard overridden
filament flush temp: 0 overridden
filament flush volumetric speed: 0 overridden
filament id: P9e57294 overridden
filament is support: 0 overridden
filament long retractions when cut: nil overridden
filament metal stickiness: None overridden
filament minimal purge on wipe tower: 15 overridden
filament notes: Updated by John Schneider on 1/6/26 @ 5:49pm Updated 2/26/26 - Set adhesiveness category to 300 overridden
filament overhang 1 4 speed: 0 overridden
filament overhang 2 4 speed: 0 overridden
filament overhang 3 4 speed: 0 overridden
filament overhang 4 4 speed: 0 overridden
filament overhang totally speed: 10 overridden
filament pre cooling temperature: 0 overridden
filament pre cooling temperature nc: 0 overridden
filament prime volume: 45 overridden
filament prime volume nc: 60 overridden
filament printable: 3 overridden
filament ramming travel time: 0 overridden
filament ramming travel time nc: 0 overridden
filament ramming volumetric speed: -1 overridden
filament ramming volumetric speed nc: -1 overridden
filament retract before wipe: 0% overridden
filament retract length nc: 10 overridden
filament retract restart extra: nil overridden
filament retract when changing layer: 1 overridden
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
filament scarf gap: 0 overridden
filament scarf height: 0% overridden
filament scarf length: 10 overridden
filament scarf seam type: none overridden
filament shrink: 100% overridden
filament soluble: 0 overridden
filament tower interface pre extrusion dist: 10 overridden
filament tower interface pre extrusion length: 0 overridden
filament tower interface print temp: -1 overridden
filament tower interface purge volume: 20 overridden
filament tower ironing area: 4 overridden
filament velocity adaptation factor: 1 overridden
filament wipe: 1 overridden
filament wipe distance: 1 overridden
filament z hop: nil overridden
filament z hop types: nil overridden
first x layer fan speed: 0 overridden
first x layer part fan speed: 0 overridden
full fan speed layer: 0 overridden
hole coef 1: 0 overridden
hole coef 2: -0.025 overridden
hole coef 3: 0.28 overridden
hole limit max: 0.25 overridden
hole limit min: 0.08 overridden
impact strength z: 0 overridden
ironing fan speed: -1 overridden
long retractions when ec: 0 overridden
no slow down for cooling on outwalls: 0 overridden
nozzle temperature range high: 300 overridden
nozzle temperature range low: 250 overridden
overhang fan speed: 90 overridden
overhang fan threshold: 10% overridden
overhang threshold participating cooling: 95% overridden
override process overhang speed: 0 overridden
pre start fan time: 2 overridden
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
required nozzle HRC: 3 overridden
retraction distances when ec: 10 overridden
slow down for layer cooling: 1 overridden
temperature vitrification: 84 overridden
version: 1.9.0.26 overridden

Raw resolved JSON

{
  "version": "1.9.0.26",
  "filament_id": "P9e57294",
  "hole_coef_1": [
    "0"
  ],
  "hole_coef_2": [
    "-0.025"
  ],
  "hole_coef_3": [
    "0.28"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "29.95"
  ],
  "filament_type": [
    "PCTG"
  ],
  "filament_wipe": [
    "1"
  ],
  "counter_coef_1": [
    "0"
  ],
  "counter_coef_2": [
    "0.025"
  ],
  "counter_coef_3": [
    "-0.11"
  ],
  "diameter_limit": [
    "50"
  ],
  "eng_plate_temp": [
    "80"
  ],
  "filament_notes": "Updated by John Schneider on 1/6/26 @ 5:49pm\n\nUpdated 2/26/26\n- Set adhesiveness category to 300",
  "filament_z_hop": [
    "nil"
  ],
  "hole_limit_max": [
    "0.25"
  ],
  "hole_limit_min": [
    "0.08"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "3D-Fuel"
  ],
  "filament_density": [
    "1.23"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "counter_limit_max": [
    "0.05"
  ],
  "counter_limit_min": [
    "-0.04"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "impact_strength_z": [
    "0"
  ],
  "ironing_fan_speed": [
    "-1"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nM106 P3 S0\n"
  ],
  "filament_printable": [
    "3"
  ],
  "filament_scarf_gap": [
    "0"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "pre_start_fan_time": [
    "2"
  ],
  "compatible_printers": [
    "Bambu Lab X1E 0.4 nozzle"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "chamber_temperatures": [
    "45"
  ],
  "filament_settings_id": [
    "3D-Fuel PCTG Pro @Bambu Lab X1E 0.4 nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_bridge_speed": [
    "25"
  ],
  "filament_prime_volume": [
    "45"
  ],
  "filament_scarf_height": [
    "0%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "cooling_slowdown_logic": [
    "uniform_cooling"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_change_length": [
    "10"
  ],
  "filament_wipe_distance": [
    "1"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "first_x_layer_fan_speed": [
    "0"
  ],
  "filament_prime_volume_nc": [
    "60"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "long_retractions_when_ec": [
    "0"
  ],
  "circle_compensation_speed": [
    "200"
  ],
  "filament_change_length_nc": [
    "10"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard"
  ],
  "filament_metal_stickiness": [
    "None"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "84"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_retract_length_nc": [
    "10"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "compatible_prints_condition": "",
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_overhang_1_4_speed": [
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "0"
  ],
  "filament_overhang_3_4_speed": [
    "0"
  ],
  "filament_overhang_4_4_speed": [
    "0"
  ],
  "filament_tower_ironing_area": [
    "4"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_dev_ams_drying_time": [
    "0"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "0%"
  ],
  "first_x_layer_part_fan_speed": [
    "0"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_range_low": [
    "250"
  ],
  "retraction_distances_when_ec": [
    "10"
  ],
  "compatible_printers_condition": "",
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_cooling_before_tower": [
    "10"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "volumetric_speed_coefficients": [
    ""
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_adhesiveness_category": [
    "300"
  ],
  "filament_enable_overhang_speed": [
    "1"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "filament_extruder_compatibility": [
    "0"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0"
  ],
  "override_process_overhang_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_dev_chamber_drying_time": [
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_adaptive_volumetric_speed": [
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_dev_ams_drying_temperature": [
    "0"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0"
  ],
  "filament_tower_interface_print_temp": [
    "-1"
  ],
  "filament_velocity_adaptation_factor": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "no_slow_down_for_cooling_on_outwalls": [
    "0"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_tower_interface_purge_volume": [
    "20"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "filament_dev_ams_drying_ams_limitations": [
    ""
  ],
  "filament_dev_drying_cooling_temperature": [
    "0"
  ],
  "overhang_threshold_participating_cooling": [
    "95%"
  ],
  "filament_dev_drying_softening_temperature": [
    "0"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "0"
  ],
  "filament_tower_interface_pre_extrusion_dist": [
    "10"
  ],
  "filament_tower_interface_pre_extrusion_length": [
    "0"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "0"
  ],
  "name": "3D-Fuel PCTG Pro @Bambu Lab X1E 0.4 nozzle",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created by root · 2026-06-17 15:53