Prusa ABS @0.8 nozzle MINI

Made for Prusa · ABS · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Prusa ABS @0.8 nozzle MINI

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*ABSMINI*

Settings

Basic information

Material variant: ABS inherited
Vendor: Made for Prusa inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 inherited
Cost (/kg): 27.82 inherited

Print temperature

Nozzle (initial layer) (°C): 265 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 265 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 15 inherited
Fan maximum (%): 15 inherited
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 20 overridden
was 20 (inherited)
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 13 overridden
was 10 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 via include	100 via include

Other settings

bridge fan speed: 25 inherited
compatible printers condition: nozzle_diameter[0]==0.8 and printer_notes=~/.*MINI.*/ overridden
was printer_notes=~/.*MINI.*/ and nozzle_diameter[0]!=0.8 (inherited)
cooling: 1 inherited
fan always on: 0 inherited
filament colour: #FFF2EC inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: nil overridden
was nil (inherited)
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 overridden
was 3 (inherited)
filament retract length: 3.2 overridden
was 2.7 (inherited)
filament retract lift: nil overridden
was nil (inherited)
filament retract speed: nil overridden
was nil (inherited)
filament soluble: 0 inherited
filament spool weight: 230 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil overridden
was 0 (inherited)
start filament gcode: M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode {if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} via *ABSMINI*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "27.82"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.6}0.12{elsif nozzle_diameter[0]==0.8}0.06{else}0.2{endif} ; Filament gcode\n\n{if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif}\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]==0.8 and printer_notes=~/.*MINI.*/"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "15"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "filament_colour": [
    "#FFF2EC"
  ],
  "bridge_fan_speed": [
    "25"
  ],
  "nozzle_temperature": [
    "265"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_max_volumetric_speed": [
    "13"
  ],
  "nozzle_temperature_initial_layer": [
    "265"
  ],
  "filament_vendor": [
    "Made for Prusa"
  ],
  "filament_spool_weight": [
    "230"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "filament_retract_speed": [
    "nil"
  ],
  "filament_retract_length": [
    "3.2"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "name": "Prusa ABS @0.8 nozzle MINI",
  "type": "filament"
}