Bambu PETG Basic @BBL A1M 0.2 nozzle

Bambu Lab · PETG · 0.20mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Bambu PETG Basic @base

→

Bambu PETG Basic @BBL A1M 0.2 nozzle

Compatible printers (1)

Bambu Lab A1 mini 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 24.99 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 20 overridden
was 10 (inherited)
Fan maximum (%): 35 overridden
was 40 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 overridden
was 30 (inherited)
Slow down if layer below (sec): 7 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.94 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 1 overridden
was 8 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255
{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab A1 mini 0.2 nozzle overridden
description: To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG. inherited
filament change length nc: 10 inherited
filament id: GFG00 inherited
filament is support: 0 inherited
filament long retractions when cut: 1 overridden
filament metal stickiness: High inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: 18 overridden
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
first x layer fan speed: 0 inherited
full fan speed layer: 0 inherited
impact strength z: 13.6 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 25% overridden
was 10% (inherited)
pre start fan time: 0 overridden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSG00_04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "7"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "1"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.",
  "filament_id": "GFG00",
  "impact_strength_z": [
    "13.6"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "first_x_layer_fan_speed": [
    "0"
  ],
  "filament_change_length_nc": [
    "10"
  ],
  "filament_metal_stickiness": [
    "High"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "setting_id": "GFSG00_04",
  "pre_start_fan_time": [
    "0"
  ],
  "compatible_printers": [
    "Bambu Lab A1 mini 0.2 nozzle"
  ],
  "filament_long_retractions_when_cut": [
    "1"
  ],
  "filament_retraction_distances_when_cut": [
    "18"
  ],
  "name": "Bambu PETG Basic @BBL A1M 0.2 nozzle"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:16
v1 created 2026-05-19 04:02