FormFutura Centaur PP @PG 0.8

FormFutura · PP · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

FormFutura Centaur PP

→

FormFutura Centaur PP @PG 0.8

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (1)

FormFutura Centaur PP @XL 0.8

Settings

Basic information

Material variant: PP inherited
Vendor: FormFutura inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.89 inherited
Cost (/kg): 70 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 70 inherited
Fan maximum (%): 70 inherited
Disable fan for first N layers: 2 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 18 via *PET08PG*
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.05 inherited
Max volumetric speed (mm³/s): 8 overridden
was 4 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 inherited	85 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.8 via *PET08PG*
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #DEE0E6 inherited
filament cooling final speed: 1 via *PET08PG*
filament cooling initial speed: 2 via *PET08PG*
filament cooling moves: 1 via *PET08PG*
filament load time: 15 via *PET08PG*
filament loading speed: 14 via *PET08PG*
filament loading speed start: 19 via *PET08PG*
filament minimal purge on wipe tower: 35 via *PET08PG*
filament ramming parameters: 120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6 via *PET08PG*
filament retract before wipe: 0 via *PET08PG*
filament retract length: 0.8 via *PET08PG*
filament retract lift: 0.15 via *PET08PG*
filament soluble: 0 inherited
filament spool weight: 212 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 via *PET08PG*
filament unloading speed: 20 via *PET08PG*
filament unloading speed start: 120 via *PET08PG*
filament wipe: 0 inherited
idle temperature: 70 via *PET08PG*
start filament gcode: M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode {endif} M142 S36 ; set heatbreak target temp via *PET08PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "70"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "0.89"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.05"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "18"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "1"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.8"
  ],
  "filament_cooling_initial_speed": [
    "2"
  ],
  "filament_unloading_speed_start": [
    "120"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "70"
  ],
  "fan_min_speed": [
    "70"
  ],
  "filament_type": [
    "PP"
  ],
  "filament_wipe": [
    "0"
  ],
  "hot_plate_temp": [
    "85"
  ],
  "filament_colour": [
    "#DEE0E6"
  ],
  "filament_vendor": [
    "FormFutura"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "filament_retract_lift": [
    "0.15"
  ],
  "filament_spool_weight": [
    "212"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_retract_length": [
    "0.8"
  ],
  "filament_retract_before_wipe": [
    "0"
  ],
  "name": "FormFutura Centaur PP @PG 0.8",
  "type": "filament"
}