Filament PM PC-ABS @XL 0.8
Filament PM · PC
· by flsun-system
· 0 downloads
Inheritance
-
*common*
→
*ABSC*
→
Filament PM PC-ABS
→
Filament PM PC-ABS @PG
→
Filament PM PC-ABS @XL
→
Filament PM PC-ABS @XL 0.8
Includes (3)
Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.
Settings
Basic information
- Material variant
-
PC inherited
- Vendor
-
Filament PM inherited
- Diameter (mm)
-
1.75 inherited
- Density (g/cm³)
-
1.19 inherited
- Cost (/kg)
-
49.90 inherited
Print temperature
- Nozzle (initial layer) (°C)
-
275 inherited
- Nozzle (other layers) (°C)
-
275 inherited
Cooling
- Fan minimum (%)
-
20 inherited
- Fan maximum (%)
-
20 inherited
- Disable fan for first N layers
-
4 inherited
- Full fan if layer below (sec)
-
30 inherited
- Slow down if layer below (sec)
-
20 inherited
- Min speed when slowed (mm/s)
-
15 inherited
Flow
- Flow ratio
-
1 inherited
- Max volumetric speed (mm³/s)
-
8 via *PCPG*
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
100
via include
|
105
via include
|
Other settings
- bridge fan speed
-
30 inherited
- compatible printers condition
-
printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.8 via *PC08XL*
- cooling
-
0 inherited
- fan always on
-
0 inherited
- filament colour
-
#DEE0E6 inherited
- filament cooling final speed
-
50 via *PCPG*
- filament cooling initial speed
-
10 via *PCPG*
- filament cooling moves
-
5 via *PCPG*
- filament load time
-
15 via *PCPG*
- filament loading speed
-
14 via *PCPG*
- filament loading speed start
-
19 via *PCPG*
- filament minimal purge on wipe tower
-
35 via *PC08XL*
- filament multitool ramming
-
1 via *PC08XL*
- filament multitool ramming flow
-
40 via *PC08XL*
- filament multitool ramming volume
-
10 via *PC08XL*
- filament ramming parameters
-
120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, via *PCPG*
- filament retract length toolchange
-
20 via *PC08XL*
- filament soluble
-
0 inherited
- filament toolchange delay
-
0 inherited
- filament travel max lift
-
1.5 via *PC08XL*
- filament travel ramping lift
-
1 via *PC08XL*
- filament travel slope
-
1 via *PC08XL*
- filament unload time
-
12 via *PCPG*
- filament unloading speed
-
20 via *PCPG*
- filament unloading speed start
-
100 inherited
- idle temperature
-
150 via *PC08XL*
- start filament gcode
-
M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.025{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode {endif} M142 S45 ; set heatbreak target temp via *PCPG*
Raw resolved JSON
{
"cooling": [
"0"
],
"filament_cost": [
"49.90"
],
"filament_notes": [
""
],
"filament_density": [
"1.19"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"end_filament_gcode": [
""
],
"filament_load_time": [
"15"
],
"compatible_printers": [
""
],
"filament_flow_ratio": [
"1"
],
"slow_down_min_speed": [
"15"
],
"filament_settings_id": [
""
],
"filament_unload_time": [
"12"
],
"slow_down_layer_time": [
"20"
],
"start_filament_gcode": [
"M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.025{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S45 ; set heatbreak target temp"
],
"filament_cooling_moves": [
"5"
],
"filament_loading_speed": [
"14"
],
"filament_unloading_speed": [
"20"
],
"filament_toolchange_delay": [
"0"
],
"filament_ramming_parameters": [
"120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
""
],
"filament_cooling_final_speed": [
"50"
],
"filament_loading_speed_start": [
"19"
],
"compatible_printers_condition": [
"printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.8"
],
"filament_cooling_initial_speed": [
"10"
],
"filament_unloading_speed_start": [
"100"
],
"filament_minimal_purge_on_wipe_tower": [
"35"
],
"fan_always_on": [
"0"
],
"fan_max_speed": [
"20"
],
"fan_min_speed": [
"20"
],
"filament_type": [
"PC"
],
"hot_plate_temp": [
"105"
],
"filament_colour": [
"#DEE0E6"
],
"bridge_fan_speed": [
"30"
],
"nozzle_temperature": [
"275"
],
"fan_cooling_layer_time": [
"30"
],
"close_fan_the_first_x_layers": [
"4"
],
"hot_plate_temp_initial_layer": [
"100"
],
"filament_max_volumetric_speed": [
"8"
],
"nozzle_temperature_initial_layer": [
"275"
],
"filament_vendor": [
"Filament PM"
],
"idle_temperature": [
"150"
],
"filament_travel_slope": [
"1"
],
"filament_travel_max_lift": [
"1.5"
],
"filament_multitool_ramming": [
"1"
],
"filament_travel_ramping_lift": [
"1"
],
"filament_multitool_ramming_flow": [
"40"
],
"filament_multitool_ramming_volume": [
"10"
],
"filament_retract_length_toolchange": [
"20"
],
"name": "Filament PM PC-ABS @XL 0.8",
"type": "filament"
}