Fiberlogy FiberFlex 40D @XL

Fiberlogy · FLEX · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*FLEX*

→

Fiberlogy FiberFlex 40D

→

Fiberlogy FiberFlex 40D @XL

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*FLEXXL*

Inherited from this (2)

Settings

Basic information

Material variant: FLEX inherited
Vendor: Fiberlogy inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.16 inherited
Cost (/kg): 39.41 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 230 (inherited)

Cooling

Fan minimum (%): 25 inherited
Fan maximum (%): 75 inherited
Disable fan for first N layers: 5 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.1 overridden
was 1.12 (inherited)
Max volumetric speed (mm³/s): 2.5 overridden
was 1.5 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

bridge fan speed: 75 inherited
compatible printers condition: printer_model=~/.*XL.*/ and nozzle_diameter[0]>=0.3 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 via *FLEXXL*
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #008000 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament deretract speed: 20 via *FLEXXL*
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 35 via *FLEXXL*
filament multitool ramming: 0 via *FLEXXL*
filament multitool ramming flow: 2.5 overridden
filament multitool ramming volume: 40 via *FLEXXL*
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 via *FLEXXL*
filament retract length: 2.2 overridden
was 1.2 (inherited)
filament retract length toolchange: 2.2 overridden
filament retract lift: 0 inherited
filament retract speed: 60 via *FLEXXL*
filament soluble: 0 inherited
filament spool weight: 330 inherited
filament toolchange delay: 0 inherited
filament travel max lift: 1.5 via *FLEXXL*
filament travel ramping lift: 1 via *FLEXXL*
filament travel slope: 1 via *FLEXXL*
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: 0 inherited
full fan speed layer: 5 inherited
idle temperature: 70 via *FLEXXL*
renamed from: Fiberlogy FiberFlex 40D @PG overridden
start filament gcode: M900 K0 ; Filament gcode M142 S36 ; set heatbreak target temp via *FLEXXL*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "39.41"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.16"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_model=~/.*XL.*/ and nozzle_diameter[0]>=0.3 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "75"
  ],
  "fan_min_speed": [
    "25"
  ],
  "filament_type": [
    "FLEX"
  ],
  "filament_wipe": [
    "0"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#008000"
  ],
  "bridge_fan_speed": [
    "75"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_retract_length": [
    "2.2"
  ],
  "filament_deretract_speed": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "5"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "2.5"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_vendor": [
    "Fiberlogy"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "filament_spool_weight": [
    "330"
  ],
  "filament_retract_speed": [
    "60"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "2.5"
  ],
  "filament_multitool_ramming_volume": [
    "40"
  ],
  "renamed_from": [
    "Fiberlogy FiberFlex 40D @PG"
  ],
  "filament_retract_length_toolchange": [
    "2.2"
  ],
  "name": "Fiberlogy FiberFlex 40D @XL",
  "type": "filament"
}