Ultrafuse PET-CF15 @PG 0.6

BASF · PET · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Ultrafuse PET-CF15 @PG 0.6

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*PET06PG*

Inherited from this (1)

Ultrafuse PET-CF15 @XL 0.6

Settings

Basic information

Material variant: PET inherited
Vendor: BASF inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.36 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 265 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 60 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 14 via *PET06PG*
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 10 overridden
was 10 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	75 inherited	75 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.6 via *PET06PG*
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #404040 inherited
filament cooling final speed: 1 via *PET06PG*
filament cooling initial speed: 2 via *PET06PG*
filament cooling moves: 1 via *PET06PG*
filament deretract speed: 30 inherited
filament load time: 15 via *PET06PG*
filament loading speed: 14 via *PET06PG*
filament loading speed start: 19 via *PET06PG*
filament minimal purge on wipe tower: 35 via *PET06PG*
filament notes: Material Description PET CF15 is a Carbon Fiber reinforced PET which has precisely tuned material properties, for a wide range of technical applications. The filament is very strong and stiff and has high heat resistance. With its high dimensional stability and low abrasiveness, the filament offers an easy to print experience which allows direct printing on glass or a PEI sheet. It is compatible with HiPS for breakaway support and water soluble support and has an excellent surface finish. Printing Recommendations: This material contains fibers that have an abrasive effect on printer components. Use a hardened nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle. Ultrafuse PET-CF15 can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion. inherited
filament ramming parameters: 120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6 via *PET06PG*
filament retract before travel: 2 inherited
filament retract before wipe: 0 via *PET06PG*
filament retract layer change: 0 inherited
filament retract length: 0.9 via *PET06PG*
filament retract lift: 0.15 via *PET06PG*
filament retract speed: 40 inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 via *PET06PG*
filament unloading speed: 20 via *PET06PG*
filament unloading speed start: 120 via *PET06PG*
filament wipe: 0 inherited
full fan speed layer: 3 inherited
idle temperature: 70 via *PET06PG*
start filament gcode: M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode {endif} M142 S36 ; set heatbreak target temp via *PET06PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nPET CF15 is a Carbon Fiber reinforced PET which has precisely tuned material properties, for a wide range of technical applications. The filament is very strong and stiff and has high heat resistance. With its high dimensional stability and low abrasiveness, the filament offers an easy to print experience which allows direct printing on glass or a PEI sheet. It is compatible with HiPS for breakaway support and water soluble support and has an excellent surface finish.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PET-CF15 can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
  ],
  "filament_density": [
    "1.36"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "14"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.07{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.09{elsif nozzle_diameter[0]==0.35}0.08{elsif nozzle_diameter[0]==0.6}0.04{elsif nozzle_diameter[0]==0.5}0.05{elsif nozzle_diameter[0]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.055{elsif nozzle_diameter[0]==0.5}0.042{elsif nozzle_diameter[0]==0.6}0.032{elsif nozzle_diameter[0]==0.8}0.018{elsif nozzle_diameter[0]==0.25}0.18{elsif nozzle_diameter[0]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "1"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.6"
  ],
  "filament_cooling_initial_speed": [
    "2"
  ],
  "filament_unloading_speed_start": [
    "120"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "60"
  ],
  "filament_type": [
    "PET"
  ],
  "hot_plate_temp": [
    "75"
  ],
  "filament_colour": [
    "#404040"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "265"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "75"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_wipe": [
    "0"
  ],
  "filament_vendor": [
    "BASF"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "filament_retract_lift": [
    "0.15"
  ],
  "filament_retract_speed": [
    "40"
  ],
  "filament_retract_length": [
    "0.9"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_deretract_speed": [
    "30"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "0"
  ],
  "name": "Ultrafuse PET-CF15 @PG 0.6",
  "type": "filament"
}