Ultrafuse PAHT-CF15 @PG 0.8
BASF · PA
· by flsun-system
· 0 downloads
Inheritance
-
*common*
→
Fillamentum Nylon FX256
→
Ultrafuse PA
→
Ultrafuse PA6 GF30
→
Ultrafuse PAHT-CF15
→
Ultrafuse PAHT-CF15 @PG 0.8
Includes (1)
Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.
Inherited from this (1)
Settings
Basic information
- Material variant
-
PA inherited
- Vendor
-
BASF inherited
- Diameter (mm)
-
1.75 inherited
- Density (g/cm³)
-
1.23 inherited
- Cost (/kg)
-
56.99 inherited
Print temperature
- Nozzle (initial layer) (°C)
-
270 inherited
- Nozzle (other layers) (°C)
-
270 inherited
Cooling
- Fan minimum (%)
-
0 inherited
- Fan maximum (%)
-
50 inherited
- Disable fan for first N layers
-
1 inherited
- Full fan if layer below (sec)
-
30 inherited
- Slow down if layer below (sec)
-
25 via *ABS08PG*
- Min speed when slowed (mm/s)
-
15 inherited
Flow
- Flow ratio
-
1 inherited
- Max volumetric speed (mm³/s)
-
18 via *ABS08PG*
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
100
inherited
|
100
inherited
|
Other settings
- bridge fan speed
-
100 inherited
- compatible printers condition
-
printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.8 via *ABS08PG*
- cooling
-
1 inherited
- fan always on
-
1 inherited
- filament colour
-
#404040 inherited
- filament cooling final speed
-
50 via *ABS08PG*
- filament cooling initial speed
-
10 via *ABS08PG*
- filament cooling moves
-
5 via *ABS08PG*
- filament load time
-
15 via *ABS08PG*
- filament loading speed
-
14 via *ABS08PG*
- filament loading speed start
-
19 via *ABS08PG*
- filament minimal purge on wipe tower
-
35 via *ABS08PG*
- filament notes
-
Material Description PAHT CF15 is a high-performance 3D printing filament that opens new application fields in FFF printing. In parallel to its advanced mechanical properties, dimensional stability, and chemical resistance, it has very good processability. It works in any FFF printer with a hardened nozzle. In addition to that, it is compatible with water-soluble support material and HiPS, which allow printing complex geometries that work in challenging environments. PAHT CF15 has high heat resistance up to 130 °C and low moisture absorption. Printing Recommendations: This material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle. Ultrafuse PAHT-CF can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion. inherited
- filament ramming parameters
-
120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, via *ABS08PG*
- filament soluble
-
0 inherited
- filament spool weight
-
230 inherited
- filament toolchange delay
-
0 inherited
- filament unload time
-
12 via *ABS08PG*
- filament unloading speed
-
20 via *ABS08PG*
- filament unloading speed start
-
100 inherited
- full fan speed layer
-
3 inherited
- idle temperature
-
100 via *ABS08PG*
- start filament gcode
-
M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} M142 S40 ; set heatbreak target temp via *ABS08PG*
Raw resolved JSON
{
"cooling": [
"1"
],
"filament_cost": [
"56.99"
],
"filament_notes": [
"Material Description\nPAHT CF15 is a high-performance 3D printing filament that opens new application fields in FFF printing. In parallel to its advanced mechanical properties, dimensional stability, and chemical resistance, it has very good processability. It works in any FFF printer with a hardened nozzle. In addition to that, it is compatible with water-soluble support material and HiPS, which allow printing complex geometries that work in challenging environments. PAHT CF15 has high heat resistance up to 130 \u00b0C and low moisture absorption.\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PAHT-CF can be printed directly onto a clean build plate. For challenging prints, use 3dLac to improve adhesion."
],
"filament_density": [
"1.23"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"end_filament_gcode": [
""
],
"filament_load_time": [
"15"
],
"compatible_printers": [
""
],
"filament_flow_ratio": [
"1"
],
"slow_down_min_speed": [
"15"
],
"filament_settings_id": [
""
],
"filament_unload_time": [
"12"
],
"slow_down_layer_time": [
"25"
],
"start_filament_gcode": [
"M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S40 ; set heatbreak target temp"
],
"filament_cooling_moves": [
"5"
],
"filament_loading_speed": [
"14"
],
"filament_unloading_speed": [
"20"
],
"filament_toolchange_delay": [
"0"
],
"filament_ramming_parameters": [
"120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
""
],
"filament_cooling_final_speed": [
"50"
],
"filament_loading_speed_start": [
"19"
],
"compatible_printers_condition": [
"printer_notes=~/.*MK4.*/ and nozzle_diameter[0]==0.8"
],
"filament_cooling_initial_speed": [
"10"
],
"filament_unloading_speed_start": [
"100"
],
"filament_minimal_purge_on_wipe_tower": [
"35"
],
"fan_always_on": [
"1"
],
"fan_max_speed": [
"50"
],
"fan_min_speed": [
"0"
],
"filament_type": [
"PA"
],
"hot_plate_temp": [
"100"
],
"filament_colour": [
"#404040"
],
"filament_vendor": [
"BASF"
],
"bridge_fan_speed": [
"100"
],
"nozzle_temperature": [
"270"
],
"filament_spool_weight": [
"230"
],
"fan_cooling_layer_time": [
"30"
],
"close_fan_the_first_x_layers": [
"1"
],
"hot_plate_temp_initial_layer": [
"100"
],
"filament_max_volumetric_speed": [
"18"
],
"nozzle_temperature_initial_layer": [
"270"
],
"full_fan_speed_layer": [
"3"
],
"idle_temperature": [
"100"
],
"name": "Ultrafuse PAHT-CF15 @PG 0.8",
"type": "filament"
}