Ultrafuse PA6 GF30 @PG 0.8

BASF · PA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

Fillamentum Nylon FX256

→

Ultrafuse PA

→

Ultrafuse PA6 GF30

→

Ultrafuse PA6 GF30 @PG 0.8

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*ABS08PG*

Inherited from this (1)

Ultrafuse PA6 GF30 @XL 0.8

Settings

Basic information

Material variant: PA inherited
Vendor: BASF inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.17 inherited
Cost (/kg): 56.99 inherited

Print temperature

Nozzle (initial layer) (°C): 275 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 275 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 25 via *ABS08PG*
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 14 overridden
was 6 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	100 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: nozzle_diameter[0]==0.8 and printer_notes=~/.*PG.*/ and ! single_extruder_multi_material overridden
was — (inherited)
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #404040 inherited
filament cooling final speed: 50 via *ABS08PG*
filament cooling initial speed: 10 via *ABS08PG*
filament cooling moves: 5 via *ABS08PG*
filament load time: 15 via *ABS08PG*
filament loading speed: 14 via *ABS08PG*
filament loading speed start: 19 via *ABS08PG*
filament minimal purge on wipe tower: 35 via *ABS08PG*
filament notes: Material Description Ultrafuse® PA6 GF30 is a unique compound specifically developed for FFF printing. Due to the glass fiber content of 30%, parts tend to warp less. In addition the excellent layer adhesion and its compatibility with the water soluble support Ultrafuse® BVOH make this material the perfect solution to develop industrial applications on an FFF printer. With its high wear and chemical resistance, high stiffness and strength, Ultrafuse® PA6 GF30 is perfect for a wide variety of applications in automotive, electronics or transportation. Ultrafuse PA6 GF30 is designed for functional prototyping and demanding applications such as industrial tooling, transportation, electronics, small appliances, sports & leisure Printing Recommendations: This material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle. Ultrafuse PA6 GF30 can be printed directly onto a clean build plate. For challenging prints, use Magigoo PA gluestick to improve adhesion. inherited
filament ramming parameters: 120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, via *ABS08PG*
filament soluble: 0 inherited
filament spool weight: 230 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 via *ABS08PG*
filament unloading speed: 20 via *ABS08PG*
filament unloading speed start: 100 inherited
full fan speed layer: 3 inherited
idle temperature: 100 via *ABS08PG*
start filament gcode: M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode {if printer_notes=~/.*(MK4IS|XLIS).*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} M142 S40 ; set heatbreak target temp via *ABS08PG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "56.99"
  ],
  "filament_notes": [
    "Material Description\nUltrafuse\u00ae PA6 GF30 is a unique compound specifically developed for FFF printing. Due to the glass fiber content of 30%, parts tend to warp less. In addition the excellent layer adhesion and its compatibility with the water soluble support Ultrafuse\u00ae BVOH make this material the perfect solution to develop industrial applications on an FFF printer.\n\nWith its high wear and chemical resistance, high stiffness and strength, Ultrafuse\u00ae PA6 GF30 is perfect for a wide variety of applications in automotive, electronics or transportation.\n\nUltrafuse PA6 GF30 is designed for functional prototyping and demanding applications such as industrial tooling, transportation, electronics, small appliances, sports & leisure\n\nPrinting Recommendations:\nThis material contains fibers that have an abrasive effect on printer components. Use a hardened or Ruby nozzle with a diameter of 0.6 or larger for optimal performance and avoid damage to the nozzle.\n\nUltrafuse PA6 GF30 can be printed directly onto a clean build plate. For challenging prints, use Magigoo PA gluestick  to improve adhesion."
  ],
  "filament_density": [
    "1.17"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "25"
  ],
  "start_filament_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.04{elsif nozzle_diameter[0]==0.25}0.1{elsif nozzle_diameter[0]==0.3}0.06{elsif nozzle_diameter[0]==0.35}0.05{elsif nozzle_diameter[0]==0.5}0.03{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.01{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "5"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
    ""
  ],
  "filament_cooling_final_speed": [
    "50"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]==0.8 and printer_notes=~/.*PG.*/ and ! single_extruder_multi_material"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_type": [
    "PA"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "filament_colour": [
    "#404040"
  ],
  "filament_vendor": [
    "BASF"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "275"
  ],
  "filament_spool_weight": [
    "230"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_max_volumetric_speed": [
    "14"
  ],
  "nozzle_temperature_initial_layer": [
    "275"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "idle_temperature": [
    "100"
  ],
  "name": "Ultrafuse PA6 GF30 @PG 0.8",
  "type": "filament"
}