Bambu TPU for AMS @BBL A1M

Bambu Lab · TPU-AMS · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Bambu TPU for AMS @base

→

Bambu TPU for AMS @BBL A1M

Compatible printers (3)

Bambu Lab A1 mini 0.4 nozzle
Bambu Lab A1 mini 0.6 nozzle
Bambu Lab A1 mini 0.8 nozzle

Settings

Basic information

Material variant: TPU-AMS inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.26 inherited
Cost (/kg): 38.99 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 230 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 40 overridden
was 50 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 10 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.97 inherited
Max volumetric speed (mm³/s): 18 inherited

Retraction

Retraction length (mm): 0.4 overridden
was 2 (inherited)
Retraction speed (mm/s): nil overridden
was 10 (inherited)
Deretraction speed (mm/s): nil overridden
was 10 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 inherited	30 inherited
Engineering Plate	30 inherited	30 inherited
High Temp Plate	35 inherited	35 inherited

Other settings

additional cooling fan speed: 70 inherited
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
compatible printers: Bambu Lab A1 mini 0.4 nozzle, Bambu Lab A1 mini 0.6 nozzle, Bambu Lab A1 mini 0.8 nozzle overridden
description: If you are to print a kind of soft TPU, please don't slice with this profile, and it is only for TPU that has high enough hardness (not less than 55D) and is compatible with the AMS. To get better printing quality, please refer to this wiki: TPU printing guide. inherited
filament id: GFU02 inherited
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
impact strength z: 9.6 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 240 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
setting id: GFSU02_03 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "38.99"
  ],
  "filament_type": [
    "TPU-AMS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "30"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.97"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "30"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "description": "If you are to print a kind of soft TPU, please don't slice with this profile, and it is only for TPU that has high enough hardness (not less than 55D) and is compatible with the AMS. To get better printing quality, please refer to this wiki: TPU printing guide.",
  "filament_id": "GFU02",
  "impact_strength_z": [
    "9.6"
  ],
  "setting_id": "GFSU02_03",
  "compatible_printers": [
    "Bambu Lab A1 mini 0.4 nozzle",
    "Bambu Lab A1 mini 0.6 nozzle",
    "Bambu Lab A1 mini 0.8 nozzle"
  ],
  "name": "Bambu TPU for AMS @BBL A1M"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:16
v1 created 2026-05-19 04:02