Ultrafuse ASA

BASF · ASA · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABSC*

→

Ultrafuse ABS

→

Ultrafuse ABS Fusion+

→

Ultrafuse ASA

Inherited from this (4)

Settings

Basic information

Material variant: ASA overridden
was ABS (inherited)
Vendor: BASF inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 overridden
was 1.08 (inherited)

Print temperature

Nozzle (initial layer) (°C): 275 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 275 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 25 overridden
was 10 (inherited)
Fan maximum (%): 50 overridden
was 20 (inherited)
Disable fan for first N layers: 4 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 5 overridden
was 11 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	110 overridden was 105	110 overridden was 100

Other settings

bridge fan speed: 100 overridden
was 25 (inherited)
compatible printers condition: printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) inherited
cooling: 1 inherited
fan always on: 0 inherited
filament colour: #FFF4CA overridden
was #FFF8D9 (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Material Description Ultrafuse ASA is a high-performance thermoplastic with similar mechanical properties as ABS. ASA offers additional benefits such as high outdoor weather resistance. The UV resistance, toughness, and rigidity make it an ideal material to 3D-print outdoor fixtures and appliances without losing its properties or color. When also taking into account the high heat resistance and high chemical resistance, this filament is a good choice for many types of applications. Printing Recommendations: Apply Magigoo PC, 3D lac or Dimafix to a clean build plate to improve adhesion. overridden
was Material Description ABS Fusion+ made with Polyscope XILOY™ 3D is an engineering filament which has been optimized for 3D-printing. This special grade has been developed in collaboration with Polyscope Polymers - renowned for its material solutions in the automotive industry. ABS is a thermoplastic which is used in many applications. Although ABS has been classified as a standard material in 3D-printing it is known to be quite challenging to process. ABS Fusion+ combines the properties of ABS with an improved processability. The filament is based on an ABS grade which can be directly printed on glass without any adhesives or tape and has a higher success rate of prints due to extreme low warping. (inherited)
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 inherited
filament retract layer change: 0 inherited
filament retract lift: 0 inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
start filament gcode: M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nUltrafuse ASA is a high-performance thermoplastic with similar mechanical properties as ABS. ASA offers additional benefits such as high outdoor weather resistance. The UV resistance, toughness, and rigidity make it an ideal material to 3D-print outdoor fixtures and appliances without losing its properties or color. When also taking into account the high heat resistance and high chemical resistance, this filament is a good choice for many types of applications.\n\nPrinting Recommendations:\nApply Magigoo PC, 3D lac or Dimafix to a clean build plate to improve adhesion."
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0\n\n{if printer_notes=~/.*PRINTER_MODEL_MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif}\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "25"
  ],
  "filament_type": [
    "ASA"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "filament_colour": [
    "#FFF4CA"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "275"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "nozzle_temperature_initial_layer": [
    "275"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_vendor": [
    "BASF"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "name": "Ultrafuse ASA",
  "type": "filament"
}