DeltiQ FP2 - TPU 92A - FlexFill (Fillamentum)

Fillamentum · TPU92A · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*DeltiQ common*

→

DeltiQ FP - FLEX - Generic

→

DeltiQ FP2 - FLEX - Generic

→

DeltiQ FP2 - TPU 92A - FlexFill (Fillamentum)

Inherited from this (1)

DeltiQ FP2 - TPU 98A - FlexFill (Fillamentum)

Settings

Basic information

Material variant: TPU92A overridden
was FLEX (inherited)
Vendor: Fillamentum overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 overridden
was 1.22 (inherited)
Cost (/kg): 58.33 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 225 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 225 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 30 (inherited)
Fan maximum (%): 70 overridden
was 50 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 20 overridden
was 20 (inherited)
Slow down if layer below (sec): 4 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 5 overridden
was 5 (inherited)

Flow

Flow ratio: 1.10 overridden
was 1.07 (inherited)
Max volumetric speed (mm³/s): 3.0 overridden
was 3.0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	50 overridden was 50	50 overridden was 50

Other settings

bridge fan speed: 80 overridden
was 80 (inherited)
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_FAMILY_DQ.*/ and printer_notes=~/.*FLEXPRINT2.*/ and nozzle_diameter[0]==0.4 inherited
cooling: 1 overridden
was 1 (inherited)
end filament gcode: ; FILAMENT_END_GCODE inherited
fan always on: 1 overridden
was 1 (inherited)
filament colour: #FF0000 inherited
filament deretract speed: nil overridden
was nil (inherited)
filament minimal purge on wipe tower: 15 inherited
filament notes: LP-CU inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 2 overridden
was 2 (inherited)
filament retract before wipe: 70% overridden
was 70% (inherited)
filament retract layer change: 0 overridden
was 0 (inherited)
filament retract length: 2.5 overridden
was 2.5 (inherited)
filament retract lift: 0.2 overridden
was 0.2 (inherited)
filament retract restart extra: nil overridden
was nil (inherited)
filament retract speed: 20 overridden
was 20 (inherited)
filament soluble: 0 inherited
filament spool weight: 229 overridden
was 250 (inherited)
filament toolchange delay: 0 inherited
filament wipe: 1 overridden
was 1 (inherited)
start filament gcode: ; FILAMENT_START_GCODE inherited

Raw resolved JSON

{
  "filament_cost": [
    "58.33"
  ],
  "filament_notes": [
    "LP-CU"
  ],
  "filament_colour": [
    "#FF0000"
  ],
  "filament_vendor": [
    "Fillamentum"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; FILAMENT_END_GCODE"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.10"
  ],
  "filament_settings_id": [
    ""
  ],
  "start_filament_gcode": [
    "; FILAMENT_START_GCODE"
  ],
  "filament_spool_weight": [
    "229"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_FAMILY_DQ.*/ and printer_notes=~/.*FLEXPRINT2.*/ and nozzle_diameter[0]==0.4"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "70"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_type": [
    "TPU92A"
  ],
  "filament_wipe": [
    "1"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "filament_density": [
    "1.22"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_retract_speed": [
    "20"
  ],
  "filament_retract_length": [
    "2.5"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "3.0"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "name": "DeltiQ FP2 - TPU 92A - FlexFill (Fillamentum)",
  "type": "filament"
}