Polymaker PolyFlex TPU95 @4Max Pro 2.0

Polymaker · FLEX · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Settings

Basic information

Material variant: FLEX overridden
Vendor: Polymaker overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.22 overridden

Print temperature

Nozzle (initial layer) (°C): 215 overridden
Nozzle (other layers) (°C): 217 overridden

Cooling

Fan minimum (%): 25 overridden
Fan maximum (%): 50 overridden
Disable fan for first N layers: 5 overridden
Full fan if layer below (sec): 45 overridden
Slow down if layer below (sec): 10 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1.04 overridden
Max volumetric speed (mm³/s): 1.65 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	55 overridden	45 overridden

Other settings

bridge fan speed: 80 overridden
compatible printers condition: printer_model=="4MAXPRO20" overridden
cooling: 1 overridden
fan always on: 1 overridden
filament colour: #FD7D2F overridden
filament deretract speed: 25 overridden
filament retract length: 4 overridden
filament retract restart extra: 0.1 overridden
filament retract speed: 60 overridden
full fan speed layer: 8 overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "25"
  ],
  "filament_type": [
    "FLEX"
  ],
  "hot_plate_temp": [
    "45"
  ],
  "filament_colour": [
    "#FD7D2F"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "nozzle_temperature": [
    "217"
  ],
  "filament_flow_ratio": [
    "1.04"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "full_fan_speed_layer": [
    "8"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "45"
  ],
  "filament_retract_speed": [
    "60"
  ],
  "filament_retract_length": [
    "4"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "close_fan_the_first_x_layers": [
    "5"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "compatible_printers_condition": [
    "printer_model==\"4MAXPRO20\""
  ],
  "filament_max_volumetric_speed": [
    "1.65"
  ],
  "filament_retract_restart_extra": [
    "0.1"
  ],
  "nozzle_temperature_initial_layer": [
    "215"
  ],
  "name": "Polymaker PolyFlex TPU95 @4Max Pro 2.0",
  "filament_settings_id": [
    "Polymaker PolyFlex TPU95 @4Max Pro 2.0"
  ],
  "type": "filament"
}