ABS predator

Unknown · ABS · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common predator*

→

*ABS predator*

Inherited from this (1)

Generic ABS @PREDATOR

Settings

Basic information

Material variant: ABS overridden
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 0 (inherited)
Cost (/kg): 20 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
Nozzle (other layers) (°C): 245 overridden

Cooling

Fan minimum (%): 0 overridden
Fan maximum (%): 0 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 20 overridden
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 10 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden	100 overridden

Other settings

bridge fan speed: 30 overridden
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_PREDATOR.*/ inherited
cooling: 0 overridden
was 0 (inherited)
fan always on: 0 overridden
filament colour: #3A80CA overridden
filament soluble: 0 inherited
top fan speed: 0 overridden

Raw resolved JSON

{
  "cooling": [
    "0"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_PREDATOR.*/"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "0"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "top_fan_speed": [
    "0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "filament_colour": [
    "#3A80CA"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "name": "*ABS predator*",
  "type": "filament"
}