Eolas Prints TPU 93A @MEGA

Eolas Prints · FLEX · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_mega*

→

*FLEX_mega*

→

Eolas Prints TPU 93A @MEGA

Settings

Basic information

Material variant: FLEX inherited
Vendor: Eolas Prints overridden
was Generic (inherited)
Density (g/cm³): 1.21 overridden
was 1.22 (inherited)
Cost (/kg): 34.99 overridden
was 82.00 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 235 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 70 inherited
Fan maximum (%): 90 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.16 overridden
was 1.15 (inherited)
Max volumetric speed (mm³/s): 1.2 overridden
was 1.2 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	30 overridden was 55	30 overridden was 50

Other settings

bridge fan speed: 80 inherited
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/ inherited
cooling: 0 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #4D9398 overridden
was #008000 (inherited)
filament deretract speed: 25 inherited
filament retract length: 0 overridden
was 0.8 (inherited)

Raw resolved JSON

{
  "fan_always_on": [
    "0"
  ],
  "filament_vendor": [
    "Eolas Prints"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/"
  ],
  "cooling": [
    "0"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "70"
  ],
  "filament_cost": [
    "34.99"
  ],
  "filament_type": [
    "FLEX"
  ],
  "hot_plate_temp": [
    "30"
  ],
  "filament_colour": [
    "#4D9398"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "filament_density": [
    "1.21"
  ],
  "nozzle_temperature": [
    "235"
  ],
  "filament_flow_ratio": [
    "1.16"
  ],
  "filament_retract_length": [
    "0"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "hot_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "1.2"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "name": "Eolas Prints TPU 93A @MEGA",
  "filament_settings_id": [
    "Eolas Prints TPU 93A @MEGA"
  ],
  "type": "filament"
}