ABS_mega

Generic · ABS · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_mega*

→

*ABS_mega*

Inherited from this (1)

Generic ABS @MEGA

Settings

Basic information

Material variant: ABS overridden
Vendor: Generic inherited
Density (g/cm³): 1.04 overridden
Cost (/kg): 27.82 overridden

Print temperature

Nozzle (initial layer) (°C): 255 overridden
Nozzle (other layers) (°C): 255 overridden

Cooling

Fan minimum (%): 20 overridden
Fan maximum (%): 30 overridden
Full fan if layer below (sec): 20 overridden
was 100 (inherited)
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Max volumetric speed (mm³/s): 11 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	105 overridden	110 overridden

Other settings

bridge fan speed: 25 overridden
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/ inherited
cooling: 0 overridden
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 overridden
was 1 (inherited)
filament colour: #3A80CA overridden
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden

Raw resolved JSON

{
  "fan_always_on": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/"
  ],
  "cooling": [
    "0"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "27.82"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "filament_colour": [
    "#3A80CA"
  ],
  "bridge_fan_speed": [
    "25"
  ],
  "filament_density": [
    "1.04"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "name": "*ABS_mega*",
  "filament_settings_id": [
    "*ABS_mega*"
  ],
  "type": "filament"
}