Generic ABS @Zonestar

Generic · ABS · by flsun-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Settings

Basic information

Material variant: ABS overridden
Vendor: Generic overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 0 overridden
Cost (/kg): 0 overridden

Print temperature

Nozzle (initial layer) (°C): 245 overridden
Nozzle (other layers) (°C): 245 overridden

Cooling

Fan minimum (%): 0 overridden
Fan maximum (%): 0 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 25 overridden
Min speed when slowed (mm/s): 15 overridden

Flow

Flow ratio: 1 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden	100 overridden

Other settings

bridge fan speed: 30 overridden
cooling: 1 overridden
fan always on: 0 overridden
filament colour: #29B2B2 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 50 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament unloading speed: 40 overridden
filament unloading speed start: 60 overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "0"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "filament_colour": [
    "#29B2B2"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "filament_density": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "slow_down_layer_time": [
    "25"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "40"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "50"
  ],
  "name": "Generic ABS @Zonestar",
  "filament_settings_id": [
    "Generic ABS @Zonestar"
  ],
  "type": "filament"
}