FLSun S1 ASA

Generic · ASA · by snapmaker-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

FLSun Generic ASA

→

FLSun S1 ASA

Compatible printers (1)

FLSun S1 0.4 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 overridden
was 1.04 (inherited)
Cost (/kg): 0 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 280 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 280 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 35 overridden
was 10 (inherited)
Fan maximum (%): 50 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 35 overridden
was 35 (inherited)
Slow down if layer below (sec): 2 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 80 overridden
was 10 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.93 (inherited)
Max volumetric speed (mm³/s): 25 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	90 overridden was 105	90 overridden was 105

Other settings

activate air filtration: 1 overridden
bed type: Cool Plate inherited
compatible printers: FLSun S1 0.4 nozzle overridden
was FLSun Q5 0.4 nozzle, FLSun QQ-S Pro 0.4 nozzle, FLSun Super Racer 0.4 nozzle, FLSun V400 0.4 nozzle (inherited)
complete print exhaust fan speed: 0 overridden
dont slow down outer wall: 1 overridden
during print exhaust fan speed: 0 overridden
filament id: GFB98 overridden
was GFB98 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 300 overridden
was 270 (inherited)
nozzle temperature range low: 240 overridden
was 240 (inherited)
overhang fan speed: 35 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 100 overridden
was 110 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "35"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": "1.05",
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "35"
  ],
  "filament_flow_ratio": "0.95",
  "slow_down_min_speed": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "25"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB98",
  "compatible_printers": [
    "FLSun S1 0.4 nozzle"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "dont_slow_down_outer_wall": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "name": "FLSun S1 ASA"
}