RatRig Generic TPU

Generic · TPU · by snapmaker-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

RatRig Generic TPU

Compatible printers (25)

RatRig V-Cast 0.4 nozzle
RatRig V-Cast 0.6 nozzle
RatRig V-Core 3 200 0.4 nozzle
RatRig V-Core 3 300 0.4 nozzle
RatRig V-Core 3 400 0.4 nozzle
RatRig V-Core 3 500 0.4 nozzle
RatRig V-Core 4 300 0.4 nozzle
RatRig V-Core 4 300 0.5 nozzle
RatRig V-Core 4 300 0.6 nozzle
RatRig V-Core 4 400 0.4 nozzle
RatRig V-Core 4 400 0.5 nozzle
RatRig V-Core 4 400 0.6 nozzle
RatRig V-Core 4 500 0.4 nozzle
RatRig V-Core 4 500 0.5 nozzle
RatRig V-Core 4 500 0.6 nozzle
RatRig V-Core 4 HYBRID 300 0.4 nozzle
RatRig V-Core 4 HYBRID 300 0.5 nozzle
RatRig V-Core 4 HYBRID 300 0.6 nozzle
RatRig V-Core 4 HYBRID 400 0.4 nozzle
RatRig V-Core 4 HYBRID 400 0.5 nozzle
RatRig V-Core 4 HYBRID 400 0.6 nozzle
RatRig V-Core 4 HYBRID 500 0.4 nozzle
RatRig V-Core 4 HYBRID 500 0.5 nozzle
RatRig V-Core 4 HYBRID 500 0.6 nozzle
RatRig V-Minion 0.4 nozzle

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 5 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 0.4 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	30 inherited	30 inherited
Engineering Plate	30 inherited	30 inherited
High Temp Plate	35 inherited	35 inherited

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: RatRig V-Core 3 200 0.4 nozzle, RatRig V-Core 3 300 0.4 nozzle, RatRig V-Core 3 400 0.4 nozzle, RatRig V-Core 3 500 0.4 nozzle, RatRig V-Minion 0.4 nozzle, RatRig V-Cast 0.4 nozzle, RatRig V-Cast 0.6 nozzle, RatRig V-Core 4 300 0.4 nozzle, RatRig V-Core 4 300 0.5 nozzle, RatRig V-Core 4 300 0.6 nozzle, RatRig V-Core 4 400 0.4 nozzle, RatRig V-Core 4 400 0.5 nozzle, RatRig V-Core 4 400 0.6 nozzle, RatRig V-Core 4 500 0.4 nozzle, RatRig V-Core 4 500 0.5 nozzle, RatRig V-Core 4 500 0.6 nozzle, RatRig V-Core 4 HYBRID 300 0.4 nozzle, RatRig V-Core 4 HYBRID 300 0.5 nozzle, RatRig V-Core 4 HYBRID 300 0.6 nozzle, RatRig V-Core 4 HYBRID 400 0.4 nozzle, RatRig V-Core 4 HYBRID 400 0.5 nozzle, RatRig V-Core 4 HYBRID 400 0.6 nozzle, RatRig V-Core 4 HYBRID 500 0.4 nozzle, RatRig V-Core 4 HYBRID 500 0.5 nozzle, RatRig V-Core 4 HYBRID 500 0.6 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFU99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 200 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
pressure advance: 0.1 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "30"
  ],
  "filament_z_hop": [
    "0"
  ],
  "hot_plate_temp": [
    "35"
  ],
  "cool_plate_temp": [
    "30"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "30"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "35"
  ],
  "cool_plate_temp_initial_layer": [
    "30"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFU99",
  "pressure_advance": [
    "0.1"
  ],
  "compatible_printers": [
    "RatRig V-Core 3 200 0.4 nozzle",
    "RatRig V-Core 3 300 0.4 nozzle",
    "RatRig V-Core 3 400 0.4 nozzle",
    "RatRig V-Core 3 500 0.4 nozzle",
    "RatRig V-Minion 0.4 nozzle",
    "RatRig V-Cast 0.4 nozzle",
    "RatRig V-Cast 0.6 nozzle",
    "RatRig V-Core 4 300 0.4 nozzle",
    "RatRig V-Core 4 300 0.5 nozzle",
    "RatRig V-Core 4 300 0.6 nozzle",
    "RatRig V-Core 4 400 0.4 nozzle",
    "RatRig V-Core 4 400 0.5 nozzle",
    "RatRig V-Core 4 400 0.6 nozzle",
    "RatRig V-Core 4 500 0.4 nozzle",
    "RatRig V-Core 4 500 0.5 nozzle",
    "RatRig V-Core 4 500 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.6 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "RatRig Generic TPU"
}