RatRig PunkFil ABS

RatRig · ABS · by snapmaker-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

RatRig PunkFil ABS

Compatible printers (25)

RatRig V-Cast 0.4 nozzle
RatRig V-Cast 0.6 nozzle
RatRig V-Core 3 200 0.4 nozzle
RatRig V-Core 3 300 0.4 nozzle
RatRig V-Core 3 400 0.4 nozzle
RatRig V-Core 3 500 0.4 nozzle
RatRig V-Core 4 300 0.4 nozzle
RatRig V-Core 4 300 0.5 nozzle
RatRig V-Core 4 300 0.6 nozzle
RatRig V-Core 4 400 0.4 nozzle
RatRig V-Core 4 400 0.5 nozzle
RatRig V-Core 4 400 0.6 nozzle
RatRig V-Core 4 500 0.4 nozzle
RatRig V-Core 4 500 0.5 nozzle
RatRig V-Core 4 500 0.6 nozzle
RatRig V-Core 4 HYBRID 300 0.4 nozzle
RatRig V-Core 4 HYBRID 300 0.5 nozzle
RatRig V-Core 4 HYBRID 300 0.6 nozzle
RatRig V-Core 4 HYBRID 400 0.4 nozzle
RatRig V-Core 4 HYBRID 400 0.5 nozzle
RatRig V-Core 4 HYBRID 400 0.6 nozzle
RatRig V-Core 4 HYBRID 500 0.4 nozzle
RatRig V-Core 4 HYBRID 500 0.5 nozzle
RatRig V-Core 4 HYBRID 500 0.6 nozzle
RatRig V-Minion 0.4 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: RatRig overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 25.5 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 10 (inherited)
Fan maximum (%): 60 overridden
was 80 (inherited)
Disable fan for first N layers: 2 overridden
was 3 (inherited)
Full fan if layer below (sec): 7 overridden
was 30 (inherited)
Slow down if layer below (sec): 2 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 50 overridden
was 10 (inherited)

Flow

Flow ratio: 0.92 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 40 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	110 overridden was 105	110 overridden was 105

Other settings

bed type: Cool Plate inherited
compatible printers: RatRig V-Core 3 200 0.4 nozzle, RatRig V-Core 3 300 0.4 nozzle, RatRig V-Core 3 400 0.4 nozzle, RatRig V-Core 3 500 0.4 nozzle, RatRig V-Minion 0.4 nozzle, RatRig V-Cast 0.4 nozzle, RatRig V-Cast 0.6 nozzle, RatRig V-Core 4 300 0.4 nozzle, RatRig V-Core 4 400 0.4 nozzle, RatRig V-Core 4 500 0.4 nozzle, RatRig V-Core 4 HYBRID 300 0.4 nozzle, RatRig V-Core 4 HYBRID 400 0.4 nozzle, RatRig V-Core 4 HYBRID 500 0.4 nozzle, RatRig V-Core 4 300 0.5 nozzle, RatRig V-Core 4 400 0.5 nozzle, RatRig V-Core 4 500 0.5 nozzle, RatRig V-Core 4 HYBRID 300 0.5 nozzle, RatRig V-Core 4 HYBRID 400 0.5 nozzle, RatRig V-Core 4 HYBRID 500 0.5 nozzle, RatRig V-Core 4 300 0.6 nozzle, RatRig V-Core 4 400 0.6 nozzle, RatRig V-Core 4 500 0.6 nozzle, RatRig V-Core 4 HYBRID 300 0.6 nozzle, RatRig V-Core 4 HYBRID 400 0.6 nozzle, RatRig V-Core 4 HYBRID 500 0.6 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFB99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 60 overridden
was 80 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
pressure advance: 0.022 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "25.5"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "RatRig"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.92"
  ],
  "slow_down_min_speed": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "7"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "40"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.022"
  ],
  "compatible_printers": [
    "RatRig V-Core 3 200 0.4 nozzle",
    "RatRig V-Core 3 300 0.4 nozzle",
    "RatRig V-Core 3 400 0.4 nozzle",
    "RatRig V-Core 3 500 0.4 nozzle",
    "RatRig V-Minion 0.4 nozzle",
    "RatRig V-Cast 0.4 nozzle",
    "RatRig V-Cast 0.6 nozzle",
    "RatRig V-Core 4 300 0.4 nozzle",
    "RatRig V-Core 4 400 0.4 nozzle",
    "RatRig V-Core 4 500 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.4 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.4 nozzle",
    "RatRig V-Core 4 300 0.5 nozzle",
    "RatRig V-Core 4 400 0.5 nozzle",
    "RatRig V-Core 4 500 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.5 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.5 nozzle",
    "RatRig V-Core 4 300 0.6 nozzle",
    "RatRig V-Core 4 400 0.6 nozzle",
    "RatRig V-Core 4 500 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 300 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 400 0.6 nozzle",
    "RatRig V-Core 4 HYBRID 500 0.6 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "RatRig PunkFil ABS"
}