PrimaSelect PVA+ @MMU2

PrimaSelect · PVA · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

PrimaSelect PVA+ @MMU2

Inherited from this (1)

PrimaSelect PVA+ @MMU2 0.8 nozzle

Settings

Basic information

Material variant: PVA overridden
Vendor: PrimaSelect overridden
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 overridden
was 0 (inherited)
Cost (/kg): 122.1 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 200 overridden
Nozzle (other layers) (°C): 195 overridden

Cooling

Fan minimum (%): 100 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 1 overridden
Full fan if layer below (sec): 100 overridden
Slow down if layer below (sec): 20 overridden
was 20 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 15 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 3.8 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 overridden	60 overridden

Other settings

bridge fan speed: 100 overridden
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material overridden
was — (inherited)
cooling: 0 overridden
was 1 (inherited)
fan always on: 0 overridden
filament colour: #FFFFD7 overridden
filament cooling final speed: 2 overridden
was 3.4 (inherited)
filament cooling initial speed: 4 overridden
was 2.2 (inherited)
filament cooling moves: 2 overridden
was 4 (inherited)
filament load time: 15 overridden
was 0 (inherited)
filament loading speed: 14 overridden
was 28 (inherited)
filament loading speed start: 19 overridden
was 3 (inherited)
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament ramming parameters: 120 110 3.83871 3.90323 3.96774 4.03226 4.09677 4.19355 4.3871 4.83871 5.67742 6.93548 8.54839 10.3226 11.9677 13.2581 14.129 14.5806| 0.05 3.8258 0.45 3.89676 0.95 4.05807 1.45 4.23548 1.95 5.18386 2.45 7.80651 2.95 11.5356 3.45 13.9872 3.95 14.7613 4.45 7.6 4.95 7.6 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 1 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
was 0 (inherited)
filament unload time: 12 overridden
was 0 (inherited)
filament unloading speed: 20 overridden
was 90 (inherited)
filament unloading speed start: 100 overridden
was 100 (inherited)
start filament gcode: M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 overridden
was — (inherited)

Raw resolved JSON

{
  "cooling": [
    "0"
  ],
  "filament_cost": [
    "122.1"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 110 3.83871 3.90323 3.96774 4.03226 4.09677 4.19355 4.3871 4.83871 5.67742 6.93548 8.54839 10.3226 11.9677 13.2581 14.129 14.5806| 0.05 3.8258 0.45 3.89676 0.95 4.05807 1.45 4.23548 1.95 5.18386 2.45 7.80651 2.95 11.5356 3.45 13.9872 3.95 14.7613 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "2"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material"
  ],
  "filament_cooling_initial_speed": [
    "4"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PVA"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#FFFFD7"
  ],
  "filament_vendor": [
    "PrimaSelect"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "195"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "3.8"
  ],
  "nozzle_temperature_initial_layer": [
    "200"
  ],
  "name": "PrimaSelect PVA+ @MMU2",
  "type": "filament"
}