Prusament PETG @VERTEXMMU2 0.8 nozzle

Prusa · PETG · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Prusament PETG @VERTEXMMU2

→

Prusament PETG @VERTEXMMU2 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 29.99 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 230 (inherited)

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 20 overridden
was 15 (inherited)
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 18 overridden
was 8 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 inherited	90 inherited

Other settings

bridge fan speed: 50 inherited
compatible printers condition: nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material overridden
was nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.6 and (printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material) (inherited)
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FF8000 inherited
filament cooling final speed: 1 inherited
filament cooling initial speed: 2 inherited
filament cooling moves: 1 inherited
filament load time: 15 inherited
filament loading speed: 14 inherited
filament loading speed start: 19 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 140 5.51613 5.6129 5.70968 5.77419 5.77419 5.74194 5.80645 5.93548 6.06452 6.19355 6.3871 6.74194 7.25806 7.87097 8.54839 9.22581 10 10.8387| 0.05 5.5032 0.45 5.63868 0.95 5.8 1.45 5.7839 1.95 6.02257 2.45 6.25811 2.95 7.08395 3.45 8.43875 3.95 9.92258 4.45 11.3419 4.95 7.6 overridden
was 120 140 4.70968 4.74194 4.77419 4.80645 4.83871 4.87097 4.90323 5 5.25806 5.67742 6.29032 7.06452 7.83871 8.3871| 0.05 4.72901 0.45 4.73545 0.95 4.83226 1.45 4.88067 1.95 5.05483 2.45 5.93553 2.95 7.53556 3.45 8.6323 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament retract length: 1.4 inherited
filament retract lift: 0.2 inherited
filament soluble: 0 inherited
filament spool weight: 201 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 inherited
filament unloading speed: 20 inherited
filament unloading speed start: 120 inherited
full fan speed layer: 5 inherited
start filament gcode: M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0 inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "29.99"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.08{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 140 5.51613 5.6129 5.70968 5.77419 5.77419 5.74194 5.80645 5.93548 6.06452 6.19355 6.3871 6.74194 7.25806 7.87097 8.54839 9.22581 10 10.8387| 0.05 5.5032 0.45 5.63868 0.95 5.8 1.45 5.7839 1.95 6.02257 2.45 6.25811 2.95 7.08395 3.45 8.43875 3.95 9.92258 4.45 11.3419 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "1"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]==0.8 and printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material"
  ],
  "filament_cooling_initial_speed": [
    "2"
  ],
  "filament_unloading_speed_start": [
    "120"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "filament_colour": [
    "#FF8000"
  ],
  "bridge_fan_speed": [
    "50"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_retract_length": [
    "1.4"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_spool_weight": [
    "201"
  ],
  "name": "Prusament PETG @VERTEXMMU2 0.8 nozzle",
  "type": "filament"
}