Verbatim BVOH @VERTEXMMU2

Verbatim · PVA · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_vertex*

→

Verbatim BVOH @VERTEX

→

Verbatim BVOH @VERTEXMMU2

Inherited from this (1)

Verbatim BVOH @VERTEXMMU2 0.8 nozzle

Settings

Basic information

Material variant: PVA overridden
was PVA (inherited)
Vendor: Verbatim overridden
was Verbatim (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.14 inherited
Cost (/kg): 193.58 inherited

Print temperature

Nozzle (initial layer) (°C): 200 overridden
was 215 (inherited)
Nozzle (other layers) (°C): 195 overridden
was 210 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 4 overridden
was 4 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: nozzle_diameter[0]!=0.8 and (printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material) overridden
was (printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material) (inherited)
cooling: 0 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 overridden
was 0 (inherited)
filament colour: #FFFFD7 inherited
filament cooling final speed: 1 overridden
was 3.4 (inherited)
filament cooling initial speed: 2 overridden
was 2.2 (inherited)
filament cooling moves: 1 overridden
was 4 (inherited)
filament load time: 15 overridden
was 0 (inherited)
filament loading speed: 14 overridden
was 28 (inherited)
filament loading speed start: 19 overridden
was 3 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 1 inherited
filament spool weight: 235 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 overridden
was 0 (inherited)
filament unloading speed: 20 overridden
was 90 (inherited)
filament unloading speed start: 100 overridden
was 100 (inherited)
start filament gcode: M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 inherited

Raw resolved JSON

{
  "cooling": [
    "0"
  ],
  "filament_cost": [
    "193.58"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.14"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 110 1.74194 1.90323 2.16129 2.48387 2.83871 3.25806 3.83871 4.6129 5.41935 5.96774| 0.05 1.69677 0.45 1.96128 0.95 2.63872 1.45 3.46129 1.95 4.99031 2.45 6.12908 2.95 8.30974 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "1"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]!=0.8 and (printer_notes=~/.*PRINTER_VENDOR_VERTEX.*/ and printer_notes=~/.*PRINTER_MODEL_(L|XL).*/ and single_extruder_multi_material)"
  ],
  "filament_cooling_initial_speed": [
    "2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PVA"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#FFFFD7"
  ],
  "filament_vendor": [
    "Verbatim"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "195"
  ],
  "filament_spool_weight": [
    "235"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "4"
  ],
  "nozzle_temperature_initial_layer": [
    "200"
  ],
  "name": "Verbatim BVOH @VERTEXMMU2",
  "type": "filament"
}