*PETG*
Unknown · PETG
· by super-system
· 0 downloads
Inheritance
-
*common*
→
*PETG*
Inherited from this (6)
Settings
Basic information
- Material variant
-
PETG overridden
- Diameter (mm)
-
1.75 inherited
- Density (g/cm³)
-
1.27 overriddenwas 0 (inherited)
- Cost (/kg)
-
0 inherited
Print temperature
- Nozzle (initial layer) (°C)
-
245 overridden
- Nozzle (other layers) (°C)
-
245 overridden
Cooling
- Fan minimum (%)
-
20 overridden
- Fan maximum (%)
-
50 overridden
- Disable fan for first N layers
-
3 overridden
- Full fan if layer below (sec)
-
20 overridden
- Slow down if layer below (sec)
-
20 inherited
- Min speed when slowed (mm/s)
-
20 overriddenwas 15 (inherited)
Flow
- Flow ratio
-
1 inherited
- Max volumetric speed (mm³/s)
-
8 overridden
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
80
overridden
|
75
overridden
|
Other settings
- cooling
-
1 inherited
- filament cooling final speed
-
3.4 inherited
- filament cooling initial speed
-
2.2 inherited
- filament cooling moves
-
4 inherited
- filament load time
-
0 inherited
- filament loading speed
-
28 inherited
- filament loading speed start
-
3 inherited
- filament minimal purge on wipe tower
-
15 inherited
- filament ramming parameters
-
120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
- filament soluble
-
0 inherited
- filament toolchange delay
-
0 inherited
- filament unload time
-
0 inherited
- filament unloading speed
-
90 inherited
- filament unloading speed start
-
100 inherited
Raw resolved JSON
{
"cooling": [
"1"
],
"filament_cost": [
"0"
],
"filament_notes": [
""
],
"filament_density": [
"1.27"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"end_filament_gcode": [
""
],
"filament_load_time": [
"0"
],
"compatible_printers": [
""
],
"filament_flow_ratio": [
"1"
],
"slow_down_min_speed": [
"20"
],
"filament_settings_id": [
""
],
"filament_unload_time": [
"0"
],
"slow_down_layer_time": [
"20"
],
"start_filament_gcode": [
""
],
"filament_cooling_moves": [
"4"
],
"filament_loading_speed": [
"28"
],
"filament_unloading_speed": [
"90"
],
"filament_toolchange_delay": [
"0"
],
"filament_ramming_parameters": [
"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
],
"filament_cooling_final_speed": [
"3.4"
],
"filament_loading_speed_start": [
"3"
],
"compatible_printers_condition": [
""
],
"filament_cooling_initial_speed": [
"2.2"
],
"filament_unloading_speed_start": [
"100"
],
"filament_minimal_purge_on_wipe_tower": [
"15"
],
"fan_max_speed": [
"50"
],
"fan_min_speed": [
"20"
],
"filament_type": [
"PETG"
],
"hot_plate_temp": [
"75"
],
"nozzle_temperature": [
"245"
],
"fan_cooling_layer_time": [
"20"
],
"close_fan_the_first_x_layers": [
"3"
],
"hot_plate_temp_initial_layer": [
"80"
],
"filament_max_volumetric_speed": [
"8"
],
"nozzle_temperature_initial_layer": [
"245"
],
"name": "*PETG*",
"type": "filament"
}