3D-Fuel Pro PCTG @XL

3D-Fuel · PCTG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

3D-Fuel Pro PCTG @XL

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (1)

3D-Fuel Pro PCTG Matte Black @XL

Settings

Basic information

Material variant: PCTG inherited
Vendor: 3D-Fuel inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.23 inherited
Cost (/kg): 29.95 inherited

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 260 inherited

Cooling

Fan minimum (%): 15 inherited
Fan maximum (%): 45 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 inherited
Slow down if layer below (sec): 9 via *PETPG*
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 10 overridden
was 10 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 via include	80 via include

Other settings

bridge fan speed: 70 inherited
compatible printers condition: printer_notes=~/.*XL.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_notes!~/.*HF_NOZZLE.*/ via *PETXL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PETPG*
cooling slowdown logic: consistent_surface via *PETPG*
enable dynamic fan speeds: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #C0C0C0 inherited
filament cooling final speed: 2.5 via *PETPG*
filament cooling initial speed: 5 via *PETPG*
filament cooling moves: 3 via *PETPG*
filament infill max crossing speed: 100 overridden
was 100 (inherited)
filament infill max speed: 0 via *PETPG*
filament load time: 10.5 via *PETPG*
filament loading speed: 10 via *PETPG*
filament loading speed start: 50 via *PETPG*
filament minimal purge on wipe tower: 35 via *PETXL*
filament multitool ramming: 1 via *PETXL*
filament multitool ramming flow: 40 via *PETXL*
filament multitool ramming volume: 10 via *PETXL*
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PETPG*
filament retract before wipe: 20 via *PETPG*
filament retract length: 0.8 via *PETPG*
filament retract length toolchange: 20 via *PETXL*
filament retract lift: 0.15 via *PETPG*
filament soluble: 0 inherited
filament stamping distance: 45 via *PETPG*
filament stamping loading speed: 26.5 via *PETPG*
filament toolchange delay: 0 via *PETPG*
filament travel max lift: 1.5 via *PETXL*
filament travel ramping lift: 1 via *PETXL*
filament travel slope: 1 via *PETXL*
filament unload time: 8.5 via *PETPG*
filament unloading speed: 60 via *PETPG*
filament unloading speed start: 60 via *PETPG*
filament wipe: 1 via *PETPG*
full fan speed layer: 3 inherited
idle temperature: 70 via *PETPG*
overhang fan speed 0: 70 inherited
overhang fan speed 1: 45 inherited
overhang fan speed 2: 30 inherited
overhang fan speed 3: 0 inherited
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Pressure advance {endif} M142 S36 ; set heatbreak target temp via *PETPG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "29.95"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#C0C0C0"
  ],
  "filament_vendor": [
    "3D-Fuel"
  ],
  "filament_density": [
    "1.23"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "9"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*XL.*/ and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_notes!~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "45"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_type": [
    "PCTG"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "bridge_fan_speed": [
    "70"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "overhang_fan_speed_0": [
    "70"
  ],
  "overhang_fan_speed_1": [
    "45"
  ],
  "overhang_fan_speed_2": [
    "30"
  ],
  "overhang_fan_speed_3": [
    "0"
  ],
  "enable_dynamic_fan_speeds": [
    "1"
  ],
  "filament_wipe": [
    "1"
  ],
  "idle_temperature": [
    "70"
  ],
  "filament_retract_lift": [
    "0.15"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_retract_length": [
    "0.8"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_retract_before_wipe": [
    "20"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "100"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "name": "3D-Fuel Pro PCTG @XL",
  "type": "filament"
}