Generic PETG @Voron HF0.8

Generic · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PETG*

→

*PETGHF*

→

Generic PETG @Voron HF0.4

→

Generic PETG @Voron HF0.8

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 245 inherited
Chamber (°C): 35 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 2 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 29 overridden
was 22 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	70 inherited	70 inherited

Other settings

bridge fan speed: 100 inherited
chamber minimal temperature: 0 inherited
compatible printers condition: printer_model=~/(V2_250|V2_300|V2_350|VT_250|VT_300|VT_350|V0_120|VS_MK52)/ and nozzle_high_flow[0] and nozzle_diameter[0]==0.8 overridden
was printer_model=~/(V2_250|V2_300|V2_350|VT_250|VT_300|VT_350|V0_120|VS_MK52)/ and nozzle_high_flow[0] and nozzle_diameter[0]==0.4 (inherited)
cooling: 1 inherited
cooling perimeter transition distance: 10 inherited
cooling slowdown logic: consistent_surface inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FF3232 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
full fan speed layer: 5 inherited
start filament gcode: ; Filament-specific start gcode inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament-specific start gcode"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(V2_250|V2_300|V2_350|VT_250|VT_300|VT_350|V0_120|VS_MK52)/ and nozzle_high_flow[0] and nozzle_diameter[0]==0.8"
  ],
  "filament_max_volumetric_speed": [
    "29"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "chamber_temperature": [
    "35"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "name": "Generic PETG @Voron HF0.8",
  "type": "filament"
}