DeltiQ - PETG - Generic
Generic · PET
· by super-system
· 0 downloads
Inheritance
-
*DeltiQ common*
→
DeltiQ - PETG - Generic
Inherited from this (2)
Settings
Basic information
- Material variant
-
PET overridden
- Vendor
-
Generic inherited
- Diameter (mm)
-
1.75 inherited
- Density (g/cm³)
-
1.27 overridden
- Cost (/kg)
-
480 overridden
Print temperature
- Nozzle (initial layer) (°C)
-
240 overridden
- Nozzle (other layers) (°C)
-
245 overridden
Cooling
- Fan minimum (%)
-
30 overridden
- Fan maximum (%)
-
50 overridden
- Disable fan for first N layers
-
3 inherited
- Full fan if layer below (sec)
-
20 overridden
- Slow down if layer below (sec)
-
5 overridden
- Min speed when slowed (mm/s)
-
10 overridden
Flow
- Flow ratio
-
1 inherited
- Max volumetric speed (mm³/s)
-
8 overridden
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
80
overridden
|
80
overridden
|
Other settings
- bridge fan speed
-
50 overridden
- compatible printers condition
-
printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_FAMILY_DQ.*/ and !(printer_notes=~/.*FLEXPRINT.*/) and nozzle_diameter[0]==0.4 inherited
- cooling
-
1 overridden
- end filament gcode
-
; FILAMENT_END_GCODE inherited
- fan always on
-
1 overridden
- filament colour
-
#FF0000 inherited
- filament deretract speed
-
25 overridden
- filament minimal purge on wipe tower
-
15 inherited
- filament ramming parameters
-
120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
- filament retract before travel
-
2 overridden
- filament retract before wipe
-
70% overridden
- filament retract layer change
-
1 overridden
- filament retract length
-
4.1 overridden
- filament retract lift
-
0.2 overridden
- filament retract speed
-
45 overridden
- filament soluble
-
0 inherited
- filament toolchange delay
-
0 inherited
- filament wipe
-
1 overridden
- start filament gcode
-
; FILAMENT_START_GCODE inherited
Raw resolved JSON
{
"filament_notes": [
""
],
"filament_colour": [
"#FF0000"
],
"filament_vendor": [
"Generic"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"end_filament_gcode": [
"; FILAMENT_END_GCODE"
],
"compatible_printers": [
""
],
"filament_flow_ratio": [
"1"
],
"filament_settings_id": [
""
],
"start_filament_gcode": [
"; FILAMENT_START_GCODE"
],
"filament_toolchange_delay": [
"0"
],
"filament_ramming_parameters": [
"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
],
"close_fan_the_first_x_layers": [
"3"
],
"compatible_printers_condition": [
"printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_FAMILY_DQ.*/ and !(printer_notes=~/.*FLEXPRINT.*/) and nozzle_diameter[0]==0.4"
],
"filament_minimal_purge_on_wipe_tower": [
"15"
],
"cooling": [
"1"
],
"fan_always_on": [
"1"
],
"fan_max_speed": [
"50"
],
"fan_min_speed": [
"30"
],
"filament_cost": [
"480"
],
"filament_type": [
"PET"
],
"filament_wipe": [
"1"
],
"hot_plate_temp": [
"80"
],
"bridge_fan_speed": [
"50"
],
"filament_density": [
"1.27"
],
"nozzle_temperature": [
"245"
],
"slow_down_min_speed": [
"10"
],
"slow_down_layer_time": [
"5"
],
"filament_retract_lift": [
"0.2"
],
"fan_cooling_layer_time": [
"20"
],
"filament_retract_speed": [
"45"
],
"filament_retract_length": [
"4.1"
],
"filament_deretract_speed": [
"25"
],
"filament_retract_before_wipe": [
"70%"
],
"hot_plate_temp_initial_layer": [
"80"
],
"filament_max_volumetric_speed": [
"8"
],
"filament_retract_layer_change": [
"1"
],
"filament_retract_before_travel": [
"2"
],
"nozzle_temperature_initial_layer": [
"240"
],
"name": "DeltiQ - PETG - Generic",
"type": "filament"
}
Version history
View full history with diffs →- v1 created 2026-05-19 13:24