← ABS @PROTON_X

History of ABS @PROTON_X

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: *common*

via parent v8 of *common* — updated

2026-05-19 13:24
Settings (5)
- compatible printers condition added printer_notes=~/.*PRINTER_VENDOR_Artillery.*/
- cooling added 1
- default fan speed removed 0
- filament flow ratio 0.9 → 1
- slow down layer time 20 → 15
via parent v7 of *common* — updated

2026-05-19 13:24
Identity / metadata
- Vendor: Generic → Unknown
Settings (16)
- bridge fan speed removed 100
- close fan the first x layers removed 3
- compatible printers added —
- cooling removed 1
- default fan speed added 0
- fan always on removed 0
- fan cooling layer time removed 10
- filament colour removed #29B2B2
- filament cost added 0
- filament density added 0
- filament flow ratio 1 → 0.9
- filament notes added —
- filament vendor removed Generic
- full fan speed layer removed 0
- slow down layer time 5 → 20
- slow down min speed 10 → 15
direct edit v1 — created

2026-05-19 13:23

Profile created at this point. No prior version to diff against.
via parent v6 of *common* — updated

2026-05-19 13:23
Identity / metadata
- Vendor: Unknown → Generic
Settings (15)
- bridge fan speed added 100
- close fan the first x layers added 3
- compatible printers removed —
- compatible printers condition removed printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
- cooling 0 → 1
- fan always on added 0
- fan cooling layer time added 10
- filament colour added #29B2B2
- filament cost removed 0
- filament density removed 0
- filament notes removed —
- filament vendor added Generic
- full fan speed layer added 0
- slow down layer time 20 → 5
- slow down min speed 15 → 10
via parent v5 of *common* — updated

2026-05-19 13:23
Settings (6)
- compatible printers added —
- compatible printers condition printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/ → printer_notes=~/.*PRINTER_VENDOR_BIQU.*/
- filament cost added 0
- filament density added 0
- filament soluble added 0
- slow down layer time 10 → 20
via parent v4 of *common* — updated

2026-05-19 13:23
Settings (6)
- compatible printers removed —
- compatible printers condition printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/ → printer_notes=~/.*PRINTER_VENDOR_GCREATE.*/
- filament cost removed 0
- filament density removed 0
- filament soluble removed 0
- slow down layer time 20 → 10
via parent v3 of *common* — updated

2026-05-19 13:23
Identity / metadata
- Material: PLA → OTHER
Settings (46)
- bridge fan speed removed 100
- close fan the first x layers removed 1
- compatible printers condition — → printer_notes=~/.*PRINTER_VENDOR_CREALITY.*/
- compatible prints removed —
- compatible prints condition removed —
- cooling 1 → 0
- end filament gcode removed ; Filament-specific end gcode ;END gcode for filament
- fan always on removed 0
- fan cooling layer time removed 600
- fan max speed removed 100
- fan min speed removed 100
- filament colour removed #29B2B2
- filament cooling final speed removed 3.4
- filament cooling initial speed removed 2.2
- filament cooling moves removed 4
- filament cost 24 → 0
- filament deretract speed removed nil
- filament flow ratio 0.92 → 1
- filament load time removed 0
- filament loading speed removed 28
- filament loading speed start removed 3
- filament max volumetric speed removed 0
- filament minimal purge on wipe tower removed 15
- filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
- filament retract before travel removed nil
- filament retract before wipe removed nil
- filament retract layer change removed nil
- filament retract length removed nil
- filament retract lift removed nil
- filament retract lift above removed nil
- filament retract lift below removed nil
- filament retract restart extra removed nil
- filament retract speed removed nil
- filament toolchange delay removed 0
- filament type removed PLA
- filament unload time removed 0
- filament unloading speed removed 90
- filament unloading speed start removed 100
- filament wipe removed nil
- hot plate temp removed 60
- hot plate temp initial layer removed 60
- nozzle temperature removed 190
- nozzle temperature initial layer removed 190
- slow down layer time 1 → 20
- slow down min speed 30 → 15
- start filament gcode removed ; Filament gcode
via parent v2 of *common* — updated

2026-05-19 13:23
Identity / metadata
- Material: OTHER → PLA
Settings (35)
- bridge fan speed added 100
- close fan the first x layers added 1
- compatible printers added —
- compatible printers condition added —
- compatible prints added —
- compatible prints condition added —
- cooling added 1
- end filament gcode ; Filament-specific end gcode → ; Filament-specific end gcode ;END gcode for filament
- fan always on added 0
- fan cooling layer time added 600
- fan max speed added 100
- fan min speed added 100
- filament colour added #29B2B2
- filament cost 0 → 24
- filament deretract speed added nil
- filament flow ratio 1 → 0.92
- filament max volumetric speed added 0
- filament retract before travel added nil
- filament retract before wipe added nil
- filament retract layer change added nil
- filament retract length added nil
- filament retract lift added nil
- filament retract lift above added nil
- filament retract lift below added nil
- filament retract restart extra added nil
- filament retract speed added nil
- filament type added PLA
- filament wipe added nil
- hot plate temp added 60
- hot plate temp initial layer added 60
- nozzle temperature added 190
- nozzle temperature initial layer added 190
- slow down layer time 20 → 1
- slow down min speed 15 → 30
- start filament gcode — → ; Filament gcode
via parent v1 of *common* — created

2026-05-19 13:23

Profile created at this point. No prior version to diff against.