Generic PVA @GCREATE - PLA and PVA Support

Generic · PVA · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PLA*

→

Generic PLA @GCREATE

→

Generic PVA @GCREATE - PLA and PVA Support

Settings

Basic information

Material variant: PVA overridden
was PLA (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 195 overridden
was 205 (inherited)
Nozzle (other layers) (°C): 195 overridden
was 210 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 100 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 overridden
was 100 (inherited)
Slow down if layer below (sec): 10 overridden
was 20 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 15 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 0 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	55 inherited	0 overridden was 60

Other settings

bridge fan speed: 75 overridden
was 100 (inherited)
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode ;END gcode for filament overridden
was — (inherited)
fan always on: 1 overridden
was 1 (inherited)
filament colour: #F5F2C4 overridden
was #FFF0E0 (inherited)
filament cooling final speed: 3.4 overridden
was 3.4 (inherited)
filament cooling initial speed: 2.2 overridden
was 2.2 (inherited)
filament cooling moves: 0 overridden
was 4 (inherited)
filament load time: 0 inherited
filament loading speed: 30 overridden
was 28 (inherited)
filament loading speed start: 30 overridden
was 3 (inherited)
filament minimal purge on wipe tower: 7 overridden
was 15 (inherited)
filament ramming parameters: 0 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 1 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
was 0 (inherited)
filament unload time: 0 overridden
was 0 (inherited)
filament unloading speed: 30 overridden
was 90 (inherited)
filament unloading speed start: 30 overridden
was 100 (inherited)
start filament gcode: ; Filament gcode overridden
was — (inherited)

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    "Generic PVA Support @GCREATE"
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n"
  ],
  "filament_cooling_moves": [
    "0"
  ],
  "filament_loading_speed": [
    "30"
  ],
  "filament_unloading_speed": [
    "30"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "0"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "30"
  ],
  "compatible_printers_condition": [
    ""
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "30"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "7"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_type": [
    "PVA"
  ],
  "hot_plate_temp": [
    "0"
  ],
  "filament_colour": [
    "#F5F2C4"
  ],
  "bridge_fan_speed": [
    "75"
  ],
  "nozzle_temperature": [
    "195"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "195"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "name": "Generic PVA @GCREATE - PLA and PVA Support",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:23